Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL (for RH Side) › 2020.02–2020.11
RM37A0E _52 Drivetrain _086859 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0418483 DIFFERENTIAL OIL SEAL(for RH Side) A

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transaxle case oil seal and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

*3: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*4: If the vehicle height has changed due to suspension or tire replacement

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
If transaxle compensation code read from ECM
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
If transaxle compensation code not read from ECM
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
for Dynamic Torque Control AWD System:

Front 4WD linear solenoid (Transfer assembly)


·

ECU data initialization

·

Disconnect system function check


Dynamic Torque Control AWD System (Click here)
for Dynamic Torque Vectoring AWD system:

Front 4WD linear solenoid (Transfer assembly)


·

ECU data initialization

·

Disconnect system function check


Dynamic Torque Vectoring AWD System (Click here)
Replacement of front bumper assembly*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*4
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Transmission Jack


The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) or frame number registration when replacing the ECM.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

If automatic transaxle assembly parts are replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


Hide 36100 2.REMOVE TRANSFER ASSEMBLY

Hide 31105H 3.REMOVE TRANSAXLE CASE OIL SEAL

a.
C338866C01
1.781,1.156 1.083,0.229 1.083,0.229 0.927,0.229 true 0.688,0.135 1.063,0.49 0.375,0.354 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the transaxle case oil seal from the transaxle housing.

NOTICE:

Do not damage the front differential case or transaxle housing.



Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C338867N01
0.708,1.573 1.323,1.573 false 0.396,1.469 0.875,1.771 0.479,0.302 10 false SST

Using SST, remove the front drive shaft oil seal RH from the front differential case.

SST
09308-00010  

NOTICE:

Do not damage the front differential case.



Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.
C338868C01
2.698,2.219 3.073,2.344 3.073,2.344 2.958,2.083 true 2.708,2.875 3.052,3.094 0.344,0.219 10 false *a 3.052,2.385 3.417,2.813 0.365,0.427 10 false SST
*a Depth


Using SST and a hammer, install the front drive shaft oil seal RH to the front differential case.

SST
09950-60011  (09951-00410)
09950-70010  (09951-07200)

Standard Depth:

21.5 to 22.5 mm (0.846 to 0.886 in.)


NOTICE:
·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.




Hide 31105H 6.INSTALL TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new transaxle case oil seal with MP grease.


b.
C338869C01
2.844,2.948 3.271,2.948 3.271,2.948 3.271,2.094 false 3,2.948 3,2.521 false 2.125,2.896 2.521,3.177 0.396,0.281 10 false *a 2.552,2.875 3.021,3.167 0.469,0.292 10 false SST
*a Depth


Using SST and a hammer, install the transaxle case oil seal to the transaxle housing.

SST
09649-17010  
09950-70010  (09951-07200)

Standard Depth:

5.5 to 6.5 mm (0.217 to 0.256 in.)


NOTICE:
·

Be sure to install the transaxle case oil seal in the correct direction.

·

Make sure to install the transaxle case oil seal as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the transaxle case oil seal.




Hide 36100 7.INSTALL TRANSFER ASSEMBLY