If the jam protection function activates during power back door operation, one of the following may be the cause: 1) improper fit of back door or a foreign object stuck in the back door, 2) malfunction in the power back door sensor assembly circuit or 3) multiplex network door ECU malfunction.
If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors have been disconnected, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
Check if there are any foreign objects interfering with back door operation.
| Result | Proceed to |
|---|---|
| There are no foreign objects | A |
| There are foreign objects | B |
A
B
Check back door operation.
Set the customize setting "System Settings" on the multi-information display to OFF.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>CUSTOMIZE PARAMETERS
This check is possible only when the "System Settings" customize setting is set to OFF on the multi-information display in the combination meter assembly. (The default setting is ON.)
Open/close the back door by hand.
Set the customize setting "System Settings" on the multi-information display to ON.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>CUSTOMIZE PARAMETERS
The "System Settings" customize setting on the multi-information display in the combination meter assembly must be set to ON for the power back door system to operate.
| Result | Proceed to |
|---|---|
| The back door fully opens and closes smoothly | A |
| The back door does not fully open and close smoothly | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| PBD Touch Sensor (Right) | Power back door sensor assembly RH signal | OFF, ON or Open | OFF: Power back door sensor assembly RH not pressed
ON: Power back door sensor assembly RH pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor (Left) | Power back door sensor assembly LH signal | OFF, ON or Open | OFF: Power back door sensor assembly LH not pressed
ON: Power back door sensor assembly LH pressed Open: Power back door sensor assembly LH circuit open |
- |
| Tester Display |
|---|
| PBD Touch Sensor (Right) |
| PBD Touch Sensor (Left) |
| Result | Proceed to |
|---|---|
| On the GTS screen, OFF or ON is displayed accordingly | A |
| On the GTS screen, OFF or ON is not displayed accordingly or Open is displayed for power back door sensor assembly RH | B |
| On the GTS screen, OFF or ON is not displayed accordingly or Open is displayed for power back door sensor assembly LH | C |
A
B
C
Replace the power back door unit assembly set with a new or known good one.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR DRIVE UNIT>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the power back door system operation.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>OPERATION CHECK
Power back door system operates normally
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the W18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W9-1 (OSR) - W18-6 (OSR) | Always | Below 1 Ω |
| W9-2 (OSRE) - W18-24 (OSE) | Always | Below 1 Ω |
| W9-1 (OSR) or W18-6 (OSR) - Body ground | Always | 10 kΩ or higher |
| W9-2 (OSRE) or W18-24 (OSE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR TOUCH SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the W18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W10-1 (OSL) - W18-26 (OSL) | Always | Below 1 Ω |
| W10-2 (OSLE) - W18-24 (OSE) | Always | Below 1 Ω |
| W10-1 (OSL) or W18-26 (OSL) - Body ground | Always | 10 kΩ or higher |
| W10-2 (OSLE) or W18-24 (OSE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG