Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display)
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM(for 8 Inch Display) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 8 Inch Display)  B15C0  GPS Antenna Connection Malfunction(short)  B15C1  GPS Antenna Connection Malfunction(break)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly*1 or antenna divider*2.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Connection Malfunction(short) Navigation antenna malfunction
·

Navigation antenna assembly*1

·

No. 2 antenna cord sub-assembly*1

·

Antenna divider*2

·

Antenna cord sub-assembly*2

·

Navigation ECU


B15C1 GPS Antenna Connection Malfunction(break) Navigation antenna power source malfunction
·

Navigation antenna assembly*1

·

No. 2 antenna cord sub-assembly*1

·

Antenna divider*2

·

Antenna cord sub-assembly*2

·

Navigation ECU



*1: w/o Heated Windshield Defroster System

*2: w/ Heated Windshield Defroster System


WIRING DIAGRAM

w/o Heated Windshield Defroster System
E362443E19
5.229,3.063 6.25,3.521 1.021,0.458 10 false Navigation ECU 0.583,1.26 2.625,1.677 2.042,0.417 10 false Navigation Antenna Assembly 0.417,3 4.021,3.229 3.604,0.229 10 false *: No. 2 Antenna Cord Sub-assembly 0.594,1.104 1.156,1.438 0.563,0.333 10 false A 5.24,2.896 5.802,3.229 0.563,0.333 10 false B 4.958,0.5 5.417,0.875 0.458,0.375 10 false 1 1.844,0.49 2.302,0.865 0.458,0.375 10 false 3 3.406,1.24 3.844,1.594 0.438,0.354 10 false *

w/ Heated Windshield Defroster System
E362443E33
5.25,3.094 6.271,3.552 1.021,0.458 10 false Navigation ECU 0.896,1.333 2.938,1.75 2.042,0.417 10 false Antenna Divider 0.417,3 4.021,3.229 3.604,0.229 10 false *: Antenna Cord Sub-assembly 0.917,1.156 1.479,1.49 0.563,0.333 10 false I 5.25,2.927 5.813,3.26 0.563,0.333 10 false B 4.958,0.5 5.417,0.875 0.458,0.375 10 false 1 1.844,0.49 2.302,0.865 0.458,0.375 10 false 2 3.406,1.24 3.844,1.594 0.438,0.354 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Check that the No. 2 antenna cord sub-assembly*1 or antenna cord sub-assembly*2 is properly installed and does not have any sharp bends, pinching or loose connections before performing the following procedure.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

*1: w/o Heated Windshield Defroster System

*2: w/ Heated Windshield Defroster System



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (w/o Heated Windshield Defroster System) B
NG (w/ Heated Windshield Defroster System) C



A

B

2.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

C

4.INSPECT ANTENNA DIVIDER
2.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Remove the No. 2 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E322997C10
0.5,1.188 0.917,1.438 0.417,0.25 0.656,3.479 1.073,3.729 0.417,0.25 1.927,3.76 2.344,3.344 false 1.854,1 2.271,0.583 false 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 2.354,3.177 2.667,3.375 0.313,0.198 10 false 1a 2.313,0.427 2.625,0.625 0.313,0.198 10 false 3a 0.656,1.229 0.969,1.427 0.313,0.198 10 false A 0.813,3.521 1.125,3.719 0.313,0.198 10 false B
*a Component without harness connected
(No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - B-1 Always Below 1 Ω
A-3a - B-1a Always Below 1 Ω
A-3 or B-1 - Body ground Always 10 kΩ or higher
A-3a or B-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

3.INSPECT NAVIGATION ANTENNA ASSEMBLY


Result:
Proceed to
OK
NG



OK

NG

4.INSPECT ANTENNA DIVIDER
a.

b.
E241596C06
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.979,1.406 1.833,1.75 1.833,1.75 1.635,1.75 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.438,1.656 1.865,1.833 0.427,0.177 10 false 2a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 6 Always 10 kΩ or higher
2 - 2a Always 243 to 267 Ω
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

5.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.

Remove the antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E437930C01
1.5,0.333 1.917,0.583 0.417,0.25 0.688,3.458 1.104,3.708 0.417,0.25 1.177,2.021 1.177,1.479 true 2.458,3.979 1.906,3.792 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.677,0.375 1.833,0.573 0.156,0.198 10 false I 1.125,2.063 1.438,2.26 0.313,0.198 10 false 2a 0.844,3.49 1,3.688 0.156,0.198 10 false B 2.531,3.906 2.844,4.104 0.313,0.198 10 false 1a
*a Component without harness connected
(Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I-2 - B-1 Always Below 1 Ω
I-2a - B-1a Always Below 1 Ω
I-2 or B-1 - Body ground Always 10 kΩ or higher
I-2a or B-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE ANTENNA DIVIDER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

6.REPLACE ANTENNA DIVIDER
a.

Replace the antenna divider with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG