Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0419081 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the hybrid control system can be started by pressing the power switch. If the steering is unlocked, the hybrid control system can also be started by pressing the power switch with the shift lever in P and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to ON (READY)
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Engine Start Request

·

L Code Check

·

S Code Check



WIRING DIAGRAM

B572357E01
0.042,1.563 1.552,1.885 1.51,0.323 10 false from Auxiliary Battery 2,1.729 2.615,1.927 0.615,0.198 10 false STOP 2.729,1.594 2.885,1.792 0.156,0.198 10 false B 2.708,1.99 3.167,2.188 0.458,0.198 10 false GND 3.146,1.802 3.458,2 0.313,0.198 10 false IC 6.333,1.833 6.646,2.031 0.313,0.198 10 false IC 6.333,3.031 6.646,3.229 0.313,0.198 10 false IC 3.5,1.594 3.656,1.792 0.156,0.198 10 false L 3.677,1.594 3.833,1.792 0.156,0.198 10 false 3 5.135,1.51 5.448,1.708 0.313,0.198 10 false 25 5.115,1.688 5.573,1.885 0.458,0.198 10 false M5 5.146,2.667 5.458,2.865 0.313,0.198 10 false 27 5.167,4.667 5.323,4.865 0.156,0.198 10 false 4 5.083,4.854 5.542,5.052 0.458,0.198 10 false H67 5.083,5.365 5.542,5.563 0.458,0.198 10 false A31 5.156,5.177 5.469,5.375 0.313,0.198 10 false 7 5.427,4.75 5.885,4.948 0.458,0.198 10 false ST2 5.427,5.354 5.885,5.552 0.458,0.198 10 false STP 3.24,5.354 3.698,5.552 0.458,0.198 10 false STP2 3.677,5.24 3.99,5.438 0.313,0.198 10 false 37 5.448,2.75 5.906,2.948 0.458,0.198 10 false ST2 5.448,1.604 5.906,1.802 0.458,0.198 10 false STP1 5.854,2.375 6.167,2.573 0.313,0.198 10 false +B 2.417,2.438 2.875,2.635 0.458,0.198 10 false A42 2.365,5.719 3.719,5.917 1.354,0.198 10 false A57 2.406,2.604 4.698,2.802 2.292,0.198 10 false Stop Light Switch Assembly 2.354,5.896 4.26,6.281 1.906,0.385 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.125,5.76 6.896,6.313 1.771,0.552 10 false Hybrid Vehicle Control ECU 5.271,3.833 6.802,4.25 1.531,0.417 10 false Certification ECU (Smart Key ECU Assembly) 2.531,1.479 2.688,1.677 0.156,0.198 10 false 7 2.542,1.875 2.698,2.073 0.156,0.198 10 false 2 5.094,0.375 5.552,0.573 0.458,0.198 10 false H48 5.135,0.188 5.448,0.385 0.313,0.198 10 false 22 5.438,0.396 5.896,0.594 0.458,0.198 10 false P 3.396,0.375 3.854,0.573 0.458,0.198 10 false P2 3.667,0.302 3.979,0.5 0.313,0.198 10 false 3 2.25,0.719 3.229,0.969 0.979,0.25 10 false H28 2.24,0.885 4.365,1.198 2.125,0.313 10 false Shift Lock Control Unit Assembly 5.083,2.854 5.542,3.052 0.458,0.198 10 false H48

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.



PROCEDURE

1.CHECK POWER SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the power switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → ACC → ON → off A
Power source mode does not change to ACC or ON B
Power source mode changes to ON but not to ACC C
Power source mode changes to ACC but not to ON D



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

C

D

2.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

7.CHECK STOP LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
Use this item to determine whether the shift lever position switch (P) is malfunctioning.
Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 223 1
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

9.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Hybrid control system start request signal status OFF or ON OFF: The power switch is not pressed
ON: With the shift lever in P and the brake pedal depressed, the power switch is pressed and held
·

When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the power switch.


OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)

NG

10.CHECK STEERING LOCK FUNCTION
5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H67 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-27 (ST2) - H67-4 (ST2) Always Below 1 Ω
H48-27 (ST2) or H67-4 (ST2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the H48 certification ECU (smart key ECU assembly) connector.


b.

Connect the H67 hybrid vehicle control ECU connector.


c.
B531739C09
1.542,0.083 1.958,0.333 0.417,0.25 1.042,1.927 1.229,1.927 1.229,1.927 1.229,1.115 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.625,0.115 1.938,0.271 0.313,0.156 10 false H48 0.771,1.865 1.271,2.104 0.5,0.24 10 false ST2
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H48-27 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1.0 V or less



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A42 stop light switch assembly connector.


b.

Disconnect the M5 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A31 hybrid vehicle control ECU connector.


d.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-25 (STP1) - A42-3 (L) Always Below 1 Ω
M5-25 (STP1) or A42-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B531739C10
1.542,0.083 1.958,0.333 0.417,0.25 2.156,1.938 1.938,1.938 1.938,1.938 1.823,1.125 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.625,0.115 2.01,0.323 0.385,0.208 10 false H48 2.188,1.865 2.688,2.104 0.5,0.24 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H48-22 (P) - Body ground Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
10.CHECK STEERING LOCK FUNCTION
a.

Check that the steering unlocks when the ignition switch is turned to ACC.

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

11.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)

NG

11.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the power switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H28 shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-22 (P) - H28-3 (P2) Always Below 1 Ω
H48-22 (P) or H28-3 (P2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR