Home › Power Source / Network › A25A-FXS, A25B-FXS (BATTERY / CHARGING) › CHARGING SYSTEM
RM37A0E _57 Power Source / Network _086913 A25A-FXS, A25B-FXS BATTERY / CHARGING _0419406 CHARGING SYSTEM C

A25A-FXS, A25B-FXS BATTERY / CHARGING  CHARGING SYSTEM  P162B87  Lost Communication with Battery Monitor Module Missing Message  


DESCRIPTION

The hybrid vehicle control ECU communicates with the battery state sensor assembly via LIN communication. If a LIN communication error is detected, the hybrid vehicle control ECU stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P162B87 Lost Communication with Battery Monitor Module Missing Message Battery state sensor assembly or hybrid vehicle control ECU communication stops for approximately 17 minutes or more with the ignition switch ON.
(1 trip detection logic)
·

Wire harness or connector

·

Battery state sensor assembly

·

Hybrid vehicle control ECU


Charge warning is not displayed DTC stored

WIRING DIAGRAM

A409155E16
2.26,2.615 2.573,2.802 0.313,0.188 10 false C65 2.26,2.771 4.427,2.979 2.167,0.208 10 false Compressor with Motor Assembly 5.281,2.875 5.594,3.063 0.313,0.188 10 false A31 5.271,3.021 7.021,3.375 1.75,0.354 10 false Hybrid Vehicle Control ECU 2.25,1.135 2.563,1.333 0.313,0.198 10 false M7 2.25,1.292 4.313,1.479 2.063,0.188 10 false Battery State Sensor Assembly 0.875,2.313 1.99,2.521 1.115,0.208 10 false Auxiliary Battery 0.781,3.281 2.635,3.469 1.854,0.188 10 false : LIN Communication Line 1.26,0.792 1.833,1.01 0.573,0.219 10 false BATT-S 5.479,0.667 5.844,0.865 0.365,0.198 10 false LIN3 5.229,0.49 5.458,0.688 0.229,0.198 10 false 8 3.688,0.49 3.844,0.688 0.156,0.198 10 false 2 2.146,0.542 2.302,0.74 0.156,0.198 10 false 1 3.688,1.979 3.844,2.177 0.156,0.198 10 false 3 3.198,2.125 3.813,2.323 0.615,0.198 10 false DOUT 3.406,0.667 3.865,0.865 0.458,0.198 10 false LIN 2.313,0.646 2.625,0.844 0.313,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Make sure to perform the necessary procedures (adjustment, calibration, initialization, or registration) after parts related to the charging system have been removed/installed or replaced.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY
a.

Check installation condition of the battery state sensor assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the M7 battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



d.
A426242C10
1.531,0.125 1.917,0.375 0.385,0.25 0.708,1.667 0.708,1.5 0.708,1.5 1.542,1.167 true 1.635,0.177 2.094,0.375 0.458,0.198 10 false M7 0.615,1.688 0.927,1.885 0.313,0.198 10 false +B 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M7-1 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY STATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - BATTERY STATE SENSOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY STATE SENSOR ASSEMBLY)
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.

Disconnect the M7 battery state sensor assembly connector.


c.

Disconnect the C65 compressor with motor assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-8 (LIN3) - M7-2 (LIN) Always Below 1 Ω
M7-2 (LIN), A31-8 (LIN3) or C65-3 (DOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTCS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTCS
a.

Check for DTCs, and note down any DTCs that are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397

b.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

c.

Turn the ignition switch off and wait for at least 30 seconds or more.


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTCS (AIR CONDITIONING SYSTEM)
5.CLEAR DTCS (AIR CONDITIONING SYSTEM)
a.

Check for DTCs, and note down any DTCs that are output.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

b.

Clear the DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 121

c.

Turn the ignition switch off and wait for at least 30 seconds or more.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS
6.CHECK FOR DTCS
a.

Turn the ignition switch to ON (READY) and wait for 17 minutes or more.


b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTC P162B87 is output A
DTCs are not output B




A

7.CHECK FOR DTCS (AIR CONDITIONING SYSTEM)

B

7.CHECK FOR DTCS (AIR CONDITIONING SYSTEM)
a.

Check for DTCs when the following conditions are met.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
Result:
Result Proceed to
DTC B1498 is output A
DTCs are not output B




A

B