This DTC is stored when the blind spot monitor sensor LH (master) detects a short to +B in the outer rear view mirror indicator LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB0 | Short to +B in Outer Mirror Indicator(Master) | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time |
·
Outer mirror LH ·
Outer rear view mirror assembly LH ·
Harness or connector ·
Blind spot monitor sensor LH (master) ·
Outer mirror control ECU assembly LH* |
*: w/ Seat Position Memory System
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Turn the ignition switch off.
Turn the ignition switch to ON.
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the M43 blind spot monitor sensor LH (master) connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M43-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Seat Position Memory System) | B |
| NG (w/o Seat Position Memory System) | C |
A
B
C
Disconnect the IND2 outer mirror LH connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M43-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the z17 outer rear view mirror assembly LH connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M43-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J23 outer mirror control ECU assembly LH connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M43-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the IND2 outer mirror LH connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M43-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J31 outer rear view mirror assembly LH connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M43-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG