Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0420015 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH (slave) detects a short to +B in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB1 Short to +B in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time


·

Outer mirror RH

·

Outer rear view mirror assembly RH

·

Harness or connector

·

Blind spot monitor sensor RH (slave)

·

Outer mirror control ECU assembly RH*



*: w/ Seat Position Memory System


WIRING DIAGRAM

w/ Seat Position Memory System
E399045E17
2.833,0.396 2.99,0.594 0.156,0.198 10 false 8 2.781,0.979 3.042,1.198 0.26,0.219 10 false 12 4.51,0.448 4.771,0.667 0.26,0.219 10 false 13 4.552,0.969 4.813,1.188 0.26,0.219 10 false 7 4.5,0.635 4.823,0.854 0.323,0.219 10 false J7 4.5,1.156 4.823,1.375 0.323,0.219 10 false J7 2.781,1.177 3.188,1.396 0.406,0.219 10 false z16 2.771,0.625 3.177,0.844 0.406,0.219 10 false z16 3.188,0.646 3.594,0.865 0.406,0.219 10 false BSR+ 3.896,0.656 4.448,0.948 0.552,0.292 10 false BDSR 4.042,1.177 4.448,1.396 0.406,0.219 10 false GND 3.219,1.156 3.625,1.375 0.406,0.219 10 false - 0.104,2.438 2.188,2.823 2.083,0.385 10 false Outer Rear View Mirror Assembly RH 3.104,2.49 4.677,2.813 1.573,0.323 10 false Outer Mirror Control ECU Assembly RH 5.438,2.677 7.094,3.031 1.656,0.354 10 false Blind Spot Monitor Sensor RH (Slave) 5.354,0.51 5.615,0.729 0.26,0.219 10 false 4 5.552,0.656 6,0.875 0.448,0.219 10 false OMIR 5.417,2.5 5.833,2.698 0.417,0.198 10 false M2 0.448,1.729 2.531,2.115 2.083,0.385 10 false Outer Mirror RH 0.448,1.542 1.063,1.74 0.615,0.198 10 false IND1

w/o Seat Position Memory System
E407665E16
2.073,0.885 2.688,1.083 0.615,0.198 10 false BSR+ 2.354,1.427 2.531,1.615 0.177,0.188 10 false E 2.573,0.865 2.781,1.104 0.208,0.24 10 false 3 2.583,1.427 2.792,1.667 0.208,0.24 10 false 11 5.073,0.917 5.281,1.156 0.208,0.24 10 false 4 5.25,1.01 5.865,1.208 0.615,0.198 10 false OMIR 5.104,2.677 5.719,2.875 0.615,0.198 10 false M2 5.104,2.833 6.75,3.188 1.646,0.354 10 false Blind Spot Monitor Sensor RH (Slave) 0.719,2.615 1.333,2.813 0.615,0.198 10 false J15 0.719,2.76 2.823,3.135 2.104,0.375 10 false Outer Rear View Mirror Assembly RH 0.938,1.802 1.552,2 0.615,0.198 10 false IND1 0.938,1.979 3.042,2.354 2.104,0.375 10 false Outer Mirror RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the M2 blind spot monitor sensor RH (slave) connector.


b.
C406586C08
1.417,0.25 1.917,0.5 0.5,0.25 1.854,1 2.344,0.563 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.563,0.292 1.875,0.49 0.313,0.198 10 false M2 2.427,0.396 2.833,0.594 0.406,0.198 10 false OMIR
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Result Proceed to
OK A
NG (w/ Seat Position Memory System) B
NG (w/o Seat Position Memory System) C



A

B

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)

C

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the IND1 outer mirror RH connector.


b.
C406586C08
1.417,0.25 1.917,0.5 0.5,0.25 1.854,1 2.344,0.563 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.563,0.292 1.875,0.49 0.313,0.198 10 false M2 2.427,0.396 2.833,0.594 0.406,0.198 10 false OMIR
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the z16 outer rear view mirror assembly RH connector.


b.
C406586C08
1.417,0.25 1.917,0.5 0.5,0.25 1.854,1 2.344,0.563 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.563,0.292 1.875,0.49 0.313,0.198 10 false M2 2.427,0.396 2.833,0.594 0.406,0.198 10 false OMIR
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the J7 outer mirror control ECU assembly RH connector.


b.
C406586C08
1.417,0.25 1.917,0.5 0.5,0.25 1.854,1 2.344,0.563 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.563,0.292 1.875,0.49 0.313,0.198 10 false M2 2.427,0.396 2.833,0.594 0.406,0.198 10 false OMIR
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the IND1 outer mirror RH connector.


b.
C406586C08
1.417,0.25 1.917,0.5 0.5,0.25 1.854,1 2.344,0.563 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.563,0.292 1.875,0.49 0.313,0.198 10 false M2 2.427,0.396 2.833,0.594 0.406,0.198 10 false OMIR
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the J15 outer rear view mirror assembly RH connector.


b.
C406586C08
1.417,0.25 1.917,0.5 0.5,0.25 1.854,1 2.344,0.563 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.563,0.292 1.875,0.49 0.313,0.198 10 false M2 2.427,0.396 2.833,0.594 0.406,0.198 10 false OMIR
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-4 (OMIR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR