Use this procedure to troubleshoot the theft deterrent system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time |
| Where | Whether the problem occurs at a specific location |
| Under what conditions? | Whether the doors were locked or unlocked, whether the ignition switch was ON, whether the hybrid control system has started. |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read and saved, the operation history information could be lost.
The operation history function uses the current system time of the GTS and the time counter inside the controlling ECU to calculate the times shown in the operation history. For this reason, before reading the operation history, first make sure that the GTS system clock is accurately set to the current time.
Read and save operation history using the GTS.
| Tester Display |
|---|
| Operation History |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with the ignition switch off.*1
Measure the auxiliary battery voltage.*2
*1: for HV Model
*2: for Gasoline Model
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check for CAN communication system DTCs.
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
A
B
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
Check the power door lock control system.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Power door lock control system is normal
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the wireless door lock control system.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Wireless door lock control system is normal
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the entry and start system (for Entry Function).
Entry and start system (for Entry Function) is normal
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the entry and start system (for Start Function).
for HV Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>OPERATION CHECK
for Gasoline Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>OPERATION CHECK
Entry and start system (for Start Function) is normal
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for HV Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for Gasoline Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
Check the lighting system (EXT).
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>OPERATION CHECK
Lighting system (EXT) is normal
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the lighting system (INT).
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>OPERATION CHECK
Lighting system (INT) is normal
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the horn system.
Horn system is normal
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Refer to Problem Symptoms Table.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table (Fault can be simulated) | A |
| Fault is not listed in Problem Symptoms Table (Fault cannot be simulated) | B |
| Fault is listed in Problem Symptoms Table | C |
A
B
C
System Description
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION
Terminals of ECU
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>TERMINALS OF ECU
Data List / Active Test
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST
Inspection
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT