If the M1 or M2 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the switch operation and sends the seat memory switch signal to the main body ECU (multiplex network body ECU) via CAN communication. The main body ECU (multiplex network body ECU) sends the reproduction signal to each outer mirror control ECU assembly via CAN communication. When receiving the reproduction signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors, which are built into the outer mirror actuator assembly, to adjust the mirror surface to the stored position.
The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: w/ Door Control Battery
When any seat memory switch (M1 or M2) is pressed, check that the driver seat moves to the memorized position.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Driver seat moves to the memorized position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the electrical remote control mirror function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Electrical remote control mirror function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mirror Memory No.1 | Mirror position memorized in memory switch M1 | OFF or ON | OFF: Not memorized
ON: Memorized |
- |
| Mirror Memory No.2 | Mirror position memorized in memory switch M2 | OFF or ON | OFF: Not memorized
ON: Memorized |
- |
| Tester Display |
|---|
| Mirror Memory No.1 |
| Mirror Memory No.2 |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mirror Memory No.1 | Mirror position memorized in memory switch M1 | OFF or ON | OFF: Not memorized
ON: Memorized |
- |
| Mirror Memory No.2 | Mirror position memorized in memory switch M2 | OFF or ON | OFF: Not memorized
ON: Memorized |
- |
| Tester Display |
|---|
| Mirror Memory No.1 |
| Mirror Memory No.2 |
ON (Memorized) appears on the screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Turn to Fully Left Position |
Turn the ignition switch to ON.
Using the outer mirror switch assembly, turn the mirror surface to the fully left position.
Press the M1 switch while the SET switch is being pressed.
Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.
Using the outer mirror switch assembly, turn the mirror surface to the fully right position.
Press the M1 switch.
Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.
| Result | Proceed to |
|---|---|
| Memory and reactivation functions on both mirrors are not normal | A |
| Memory and reactivation function on driver door mirror is not normal | B |
| Memory and reactivation function on front passenger door mirror is not normal | C |
A
B
C
Remove the outer mirror actuator assembly (driver door).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Disconnect the z17 outer mirror control ECU assembly (driver door) connector.
| *a | Front view of wire harness connector(to Outer Mirror Control ECU Assembly (Driver Door)) |
| *b | Front view of wire harness connector(to Outer Mirror Actuator Assembly (Driver Door)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z17-6 (VSRL) - D-2 | Always | Below 1 Ω |
| z17-6 (VSRL) or D-2 - Body ground | Always | 10 kΩ or higher |
| z17-5 (VC) - D-3 | Always | Below 1 Ω |
| z17-5 (VC) or D-3 - Body ground | Always | 10 kΩ or higher |
| z17-13 (HSRL) - D-1 | Always | Below 1 Ω |
| z17-13 (HSRL) or D-1 - Body ground | Always | 10 kΩ or higher |
| z17-14 (E1) - D-4 | Always | Below 1 Ω |
| z17-14 (E1) - D-4 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the outer mirror actuator assembly (driver door) with a new or known good one.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Turn to Fully Left Position |
Turn the ignition switch to ON.
Using the outer mirror switch assembly, turn the mirror surface to the fully left position.
Press the M1 switch while the SET switch is being pressed.
Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.
Using the outer mirror switch assembly, turn the mirror surface to the fully right position.
Press the M1 switch.
Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror actuator assembly (front passenger door).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Disconnect the z16 outer mirror control ECU assembly (front passenger door) connector.
| *a | Front view of wire harness connector(to Outer Mirror Control ECU Assembly (Front Passenger Door)) |
| *b | Front view of wire harness connector(to Outer Mirror Actuator Assembly (Front Passenger Door)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z16-6 (VSSR) - E-2 | Always | Below 1 Ω |
| z16-6 (VSSR) or E-2 - Body ground | Always | 10 kΩ or higher |
| z16-5 (VC) - E-3 | Always | Below 1 Ω |
| z16-5 (VC) or E-3 - Body ground | Always | 10 kΩ or higher |
| z16-13 (HSSR) - E-1 | Always | Below 1 Ω |
| z16-13 (HSSR) or E-1 - Body ground | Always | 10 kΩ or higher |
| z16-14 (E1) - E-4 | Always | Below 1 Ω |
| z16-14 (E1) or D-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the outer mirror actuator assembly (front passenger door) with a new or known good one.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Turn to Fully Left Position |
Turn the ignition switch to ON.
Using the outer mirror switch assembly, turn the mirror surface to the fully left position.
Press the M1 switch while the SET switch is being pressed.
Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.
Using the outer mirror switch assembly, turn the mirror surface to the fully right position.
Press the M1 switch.
Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG