Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/o Memory)
RM37A0E _59 Vehicle Exterior _086891 MIRROR (EXT) _0420034 POWER MIRROR CONTROL SYSTEM(w/o Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/o Memory)  Mirror Heater does not Operate with Rear Defogger Switch  


DESCRIPTION

When the mirror heater switch (rear window defogger switch) on the air conditioning control assembly is pressed, the operation signal is sent to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the DEF relay and MIR HTR relay to operate the mirror heaters.

WIRING DIAGRAM

B563010E02
0.865,6.344 4.531,6.542 3.667,0.198 10 false : LIN Communication Line 0.927,5.531 3.021,6.333 2.094,0.802 10 false Rear Window Defogger Switch (Air Conditioning Control Assembly) 3.917,5.552 6.49,5.958 2.573,0.406 10 false Air Conditioning Amplifier Assembly 4.396,4.656 5.01,4.854 0.615,0.198 10 false RDFG 0.26,2.635 1.125,3.073 0.865,0.438 10 false from Auxiliary Battery 0.188,3.271 1.146,3.875 0.958,0.604 10 false from IG1-NO. 1 Relay 1.229,3.417 3.219,3.615 1.99,0.198 10 false ECU-IG1 NO. 3 1.583,2.792 2.854,3.135 1.271,0.344 10 false DEF 2.521,3.781 2.979,3.979 0.458,0.198 10 false DEF 1.438,1.021 2.51,1.219 1.073,0.198 10 false MIR HTR 5.438,1.167 6.979,1.594 1.542,0.427 10 false Outer Mirror LH 4.833,1.688 7.125,2.25 2.292,0.563 10 false Outer Rear View Mirror Assembly LH 6.604,0.75 6.76,0.948 0.156,0.198 10 false E 6.594,2.729 6.75,2.927 0.156,0.198 10 false E 5.438,3.125 7.125,3.417 1.688,0.292 10 false Outer Mirror RH 4.771,3.656 7.083,4.198 2.313,0.542 10 false Outer Rear View Mirror Assembly RH 5.115,2.719 5.271,2.917 0.156,0.198 10 false + 5.104,0.75 5.26,0.948 0.156,0.198 10 false + 4.396,5.094 5.01,5.292 0.615,0.198 10 false LIN1 2.302,5.115 2.917,5.313 0.615,0.198 10 false LIN1 0.26,0.823 1.125,1.26 0.865,0.438 10 false from Auxiliary Battery 3.677,1.51 4.75,1.708 1.073,0.198 10 false MIR HTR 4.844,1.542 5.302,1.74 0.458,0.198 10 false J31 4.781,3.51 5.198,3.75 0.417,0.24 10 false J15 6.771,2.708 7.083,2.906 0.313,0.198 10 false 11 6.792,0.74 7.104,0.938 0.313,0.198 10 false 11 4.896,2.708 5.052,2.906 0.156,0.198 10 false 6 4.906,0.74 5.063,0.938 0.156,0.198 10 false 6 4.302,0.74 4.458,0.938 0.156,0.198 10 false 3 4.302,1.125 4.458,1.323 0.156,0.198 10 false 1 3.542,0.74 3.698,0.938 0.156,0.198 10 false 5 3.542,1.115 3.698,1.313 0.156,0.198 10 false 2 2.063,2.542 2.219,2.74 0.156,0.198 10 false 5 2.063,3.167 2.219,3.365 0.156,0.198 10 false 2 3.125,2.26 3.281,2.458 0.156,0.198 10 false 3 3.125,3.167 3.281,3.365 0.156,0.198 10 false 1 2.073,1.979 2.229,2.177 0.156,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the auxiliary battery voltage becomes low, auxiliary battery load control will operate in order to ensure sufficient power is supplied to the power steering system. In this case, the window defogger system may not operate.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Defogger Relay (Rear) Mirror Heater OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Defogger Relay (Rear)
50004 121 22

Result:
Result Proceed to
Mirror heater operation on both mirrors is not normal A
Mirror heater operation on RH side mirror is not normal B
Mirror heater operation on LH side mirror is not normal C



A

2.CHECK WINDOW DEFOGGER SYSTEM

B

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - MIR HTR RELAY AND BODY GROUND)

C

9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - DEF RELAY AND BODY GROUND)
2.CHECK WINDOW DEFOGGER SYSTEM
a.

Check the window defogger system operation.

Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>OPERATION CHECK

OK:

The window defogger system operates normally.



Result:
Proceed to
OK
NG



OK

3.INSPECT MIR HTR RELAY

NG

3.INSPECT MIR HTR RELAY
a.

Remove the MIR HTR relay from No. 1 engine room relay block and No. 1 junction block assembly.


b.

Inspect the MIR HTR relay.

i.
B563012

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY POWER SOURCE AND BODY GROUND)

NG

REPLACE MIR HTR RELAY

4.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY POWER SOURCE AND BODY GROUND)
a.
B563011C02
0.979,0.469 1.292,0.667 0.313,0.198 10 false *a 0.135,0.135 0.448,0.333 0.313,0.198 10 false *1
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*a MIR HTR Relay holder terminals


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MIR HTR relay holder terminal 5 - Body ground Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MIR HTR relay holder terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (DEF RELAY - MIR HTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DEF RELAY - MIR HTR RELAY)
a.

Remove the DEF relay from No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DEF relay holder terminal 3 - MIR HTR relay holder terminal 2 Always Below 1 Ω
DEF relay holder terminal 3 or MIR HTR relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH/RH - MIR HTR RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH/RH - MIR HTR RELAY AND BODY GROUND)
a.

Disconnect the J31 outer rear view mirror assembly LH connector.


b.

Disconnect the J15 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J31-6 (+) - MIR HTR relay holder terminal 3 Always Below 1 Ω
J31-6 (+) or MIR HTR relay holder terminal 3 - Body ground Always 10 kΩ or higher
J31-11 (E) - Body ground Always Below 1 Ω
J15-6 (+) - MIR HTR relay holder terminal 3 Always Below 1 Ω
J15-6 (+) or MIR HTR relay holder terminal 3 - Body ground Always 10 kΩ or higher
J15-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - MIR HTR RELAY AND BODY GROUND)
a.

Remove the MIR HTR relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the J31 outer rear view mirror assembly LH connector.


c.

Disconnect the J15 outer rear view mirror assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J15-6 (+) - MIR HTR relay holder terminal 3 Always Below 1 Ω
J15-11 (E) - Body ground Always Below 1 Ω
J15-6 (+) or MIR HTR relay holder terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT OUTER MIRROR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT OUTER MIRROR RH

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION

OK:

Outer mirror RH is normal.


Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - DEF RELAY AND BODY GROUND)
a.

Remove the MIR HTR relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the J31 outer rear view mirror assembly LH connector.


c.

Disconnect the J15 outer rear view mirror assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J31-6 (+) - MIR HTR relay holder terminal 3 Always Below 1 Ω
J31-11 (E) - Body ground Always Below 1 Ω
J31-6 (+) or MIR HTR relay holder terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT OUTER MIRROR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT OUTER MIRROR LH

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION

OK:

Outer mirror LH is normal.


Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG