Home › Drivetrain › GF2A (TRANSFER / 4WD / AWD) › TRANSFER CASE FRONT OIL SEAL (for RH Side)
RM37A0E _52 Drivetrain _086861 GF2A TRANSFER / 4WD / AWD _0420304 TRANSFER CASE FRONT OIL SEAL(for RH Side) A

GF2A TRANSFER / 4WD / AWD  TRANSFER CASE FRONT OIL SEAL(for RH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transfer case oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform "Calibration"


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 43457 2.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 36113D 3.REMOVE TRANSFER CASE OIL SEAL RH

a.
C426192C01
1.208,1.271 1.542,1.427 false 1.521,0.875 1.427,0.875 1.427,0.875 1.375,1.104 false 1.573,1.365 1.885,1.521 0.313,0.156 10 false *1 1.552,0.802 1.896,1 0.344,0.198 10 false SST
*1 Transfer Case Oil Seal RH


Using SST, remove the transfer case oil seal RH from the transfer assembly.

SST
09308-00010  

NOTICE:

Do not scratch the press-fitting surface of the transfer case oil seal RH.



Hide 36113D 4.INSTALL TRANSFER CASE OIL SEAL RH

a.

Coat the lip of a new transfer case oil seal RH with MP grease.


b.
C426193C01
1.854,0.208 1.719,0.208 1.719,0.208 1.542,0.5 false 2.531,2.219 2.365,2.219 2.365,2.219 2.125,2 true 1.677,2.635 1.51,2.635 1.51,2.635 1.292,2.385 true 1.083,0.25 1.219,0.25 1.219,0.25 1.375,0.625 true 0.917,0.177 1.229,0.333 0.313,0.156 10 false *1 2.604,2.135 2.917,2.333 0.313,0.198 10 true SST 1.927,0.135 2.24,0.333 0.313,0.198 10 false SST 1.75,2.563 2.063,2.76 0.313,0.198 10 true SST 2.031,0.531 2.344,0.688 0.313,0.156 10 false *a
*1 Transfer Case Oil Seal RH
*a Depth


Using SST and a hammer, tap in the transfer case oil seal RH to the transfer assembly as shown in the illustration.

SST
09631-32020  
09950-60021  (09951-00680)
09950-70010  (09951-07360)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Tap the transfer case oil seal RH uniformly so that the transfer case oil seal RH is straight.

·

Do not tap the transfer case oil seal RH in too far.




Hide 43457 5.INSTALL DRIVE SHAFT BEARING BRACKET