Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 2GR-FKS) › 2020.02–2020.11
RM37A0E _52 Drivetrain _086862 DRIVE SHAFT / PROPELLER SHAFT _0421213 FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEELS

Hide 53852B 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851D 3.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 5.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443C 6.REMOVE REAR ENGINE UNDER COVER RH

Hide 53737B 7.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 8.REMOVE FRONT FENDER APRON SEAL RH

Hide 10.DRAIN TRANSFER OIL

Hide 43502H 11.REMOVE FRONT AXLE SHAFT NUT

a.
C415886N01
2.385,1.125 2.385,0.646 2.385,0.646 2.708,0.646 true 2.74,0.552 3.115,0.74 0.375,0.188 10 true SST

Using SST and a hammer, release the staked part of the front axle shaft nut.

SST
09930-00010  

NOTICE:

Fully loosen the staked part of the front axle shaft nut, otherwise the threads of the drive shaft may be damaged.



b.

While applying the brakes, using a 30 mm deep socket wrench, remove the front axle shaft nut.


Hide 89543 12.SEPARATE FRONT SPEED SENSOR

Hide 45470 13.SEPARATE TIE ROD ASSEMBLY

Hide 48810 14.SEPARATE FRONT STABILIZER LINK ASSEMBLY

Hide 48069 15.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 16.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Hide 43420 17.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C415887N01
1.844,0.99 1.26,1.927 1.26,1.927 1.948,1.333 true 1.042,1.938 1.5,2.135 0.458,0.198 10 false SST

Using SST, remove the front drive shaft assembly LH.

SST
09520-01011  
09520-20010  (09521-02010, 09521-02040, 09521-02060)

NOTICE:
·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly LH.




Hide 43410 18.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

a.
C415889

Separate the drive shaft bearing bracket hole snap ring from the drive shaft bearing bracket.


b.

Remove the No. 1 drive shaft bearing bracket setting bolt and front drive shaft assembly RH from the transfer assembly.

NOTICE:
·

Do not damage the transfer case oil seal RH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly RH.



HINT:

If it is difficult to disengage the fitting, tap the end of the front drive inboard joint assembly with a brass bar and a hammer.



c.

Remove the drive shaft bearing bracket hole snap ring from the front drive shaft assembly RH.


Hide 43420G 19.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

a.
C183640

Using a screwdriver, remove the front drive shaft hole snap ring.