Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › 2020.02–2020.11
RM37A0E _55 Steering _086876 STEERING GEAR / LINKAGE _0420315 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rack and pinion power steering gear assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC is output (Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD:(Click here)
for 4WD/AWD:(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front bumper assembly*2
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
·

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)


·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment Perform "Calibration".
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Rack and pinion power steering gear assembly
·

Perform torque sensor zero point calibration

·

Assist map writing


·

DTCs are output

·

EPS warning light illuminates


(Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

*3: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
Replacement of ECM
(If transaxle compensation code read from ECM)
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of ECM
(If transaxle compensation code not read from ECM)
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front bumper assembly*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Rack and pinion power steering gear assembly
·

Perform torque sensor zero point calibration

·

Assist map writing


·

DTCs are output

·

EPS warning light illuminates


(Click here)

CAUTION:
·
A346363C08
0,0 0,0 false
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

a.

When handling the rack and pinion power steering gear assembly:

i.

Do not subject the rack and pinion power steering gear assembly (especially the motor and torque sensor) to any impact. Replace the rack and pinion power steering gear assembly with a new one if subjected to a strong impact.


ii.

Do not pull the wire harness when moving the rack and pinion power steering gear assembly.


iii.

When the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



b.

When disconnecting or reconnecting the connectors:

i.

Before disconnecting connectors related to the power steering system, turn the ignition switch to ON, center the steering wheel, turn the ignition switch off, and then disconnect the connectors.


ii.

Before reconnecting connectors related to the power steering system, ensure that the ignition switch is off. Then center the steering wheel and turn the ignition switch to ON.

NOTICE:

Do not turn the ignition switch to ON when the steering wheel is not centered.



iii.

If the above operations are not carried out properly, the steering center point (zero point) will deviate, which may lead to a difference in steering effort between turning right and left.

HINT:

If there is a difference in steering effort between turning right and left, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION




Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3. SECURE STEERING WHEEL

a.
C424038

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 4.REMOVE FRONT WHEELS

Hide 45220 5.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C424039C01
1.104,2.865 1.677,2.865 true 1.292,2.875 1.292,2.948 1.292,2.948 1.646,2.948 true 0.917,2.771 1.083,2.938 0.167,0.167 10 true *a
*a Matchmark


Remove the bolt and slide the steering intermediate shaft assembly.

NOTICE:

Do not separate the steering intermediate shaft assembly from the rack and pinion power steering gear assembly.



b.

Put matchmarks on the rack and pinion power steering gear assembly and steering intermediate shaft assembly.


c.

Separate the steering intermediate shaft assembly from the rack and pinion power steering gear assembly.


Hide 45470 6.SEPARATE TIE ROD ASSEMBLY LH

a.
C424040

Remove the cotter pin and nut.


b.
C424041N01
2.292,1.604 2.292,1.188 2.292,1.188 2.365,1.188 false 2.292,1.438 2.365,1.438 false 2.219,1.625 2.677,1.823 0.458,0.198 10 false SST

Install SST to the tie rod assembly LH as shown in the illustration.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the upper ends of the tie rod assembly LH and SST are aligned.



c.

Using SST, separate the tie rod assembly LH from the steering knuckle LH as shown in the illustration.

SST
09960-20010  (09961-02010)

C424042C01
0.583,0.24 0.688,0.24 0.688,0.24 0.927,0.552 true 1.146,2.219 1.146,2.563 1.146,2.563 1.021,2.563 false 3.25,2.625 3.344,2.625 3.344,2.625 3.719,1.917 false 1.427,2.573 1.552,2.573 1.552,2.573 1.552,2.073 true 0.406,0.156 0.594,0.323 0.188,0.167 10 true *a 5.479,0.25 5.792,0.406 0.313,0.156 10 false *b 6.531,2.323 6.844,2.479 0.313,0.156 10 false *c 0.885,2.479 1.198,2.635 0.313,0.156 10 false *d 5.49,0.656 5.802,0.813 0.313,0.156 10 false *b 0.313,1.594 0.625,1.75 0.313,0.156 10 false A 0.313,2 0.625,2.156 0.313,0.156 10 false B 2.969,2.542 3.427,2.74 0.458,0.198 10 false SST 1.271,2.479 1.521,2.635 0.25,0.156 10 false *e
*a String *b Molybdenum Grease Application Area
*c Place wrench here *d Center Nut
*e Spacer - -
V113147

Turn - -


CAUTION:

Apply molybdenum grease to the threads and end of the SST bolt.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part shown in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle LH.

·

Make sure that SST is securely positioned on the spacer.

·

If the steering knuckle spacer has come off, replace the steering knuckle with a new one.




Hide 45460 7.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45319 9.REMOVE STEERING GEAR HEAT INSULATOR

a.
C424043

Remove the 2 bolts and steering gear heat insulator from the rack and pinion power steering gear assembly.


Hide 10.DISCONNECT WIRE HARNESS

a.

Disconnect the wire harness connector from the rack and pinion power steering gear assembly.

C424044

HINT:

Release the lock before rotating the lock lever.



b.

Remove the 2 bolts and separate the wire harness from the rack and pinion power steering gear assembly.


Hide 23825 11.REMOVE FUEL DELIVERY GUARD (for A25A-FXS, A25B-FXS)

Hide 13.REMOVE FRONT FRAME ASSEMBLY

Hide 14.REMOVE FRONT STABILIZER BAR SUB-ASSEMBLY WITH LINK

a.

Remove the 4 bolts and front stabilizer bar sub-assembly with the 2 front stabilizer links from the front frame assembly.

C427555


Hide 44250 15.REMOVE RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.
C424046

Remove the 4 bolts, 4 nuts and rack and pinion power steering gear assembly from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 44250 16.SECURE RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.
C424047C01
1.448,1.01 2.156,1.406 2.156,1.406 2.24,1.406 false 0.906,0.281 0.99,0.281 0.99,0.281 1.177,0.688 false 2.281,1.323 2.594,1.479 0.313,0.156 10 false *a 0.594,0.208 1.052,0.406 0.458,0.198 10 false SST
*a Protective Tape


Using SST, secure the rack and pinion power steering gear assembly in a vise.

SST
09612-00012  

HINT:

Wrap SST with protective tape before use.



Hide 45470 17.REMOVE TIE ROD ASSEMBLY LH

a.
C424048C01
1.438,0.552 1.875,0.552 1.875,0.552 1.875,1.25 true 1.667,1.26 1.667,0.563 true 1.24,0.469 1.542,0.625 0.302,0.156 10 false *a
*a Matchmark


Put matchmarks on the tie rod assembly LH and rack and pinion power steering gear assembly.


b.

Remove the tie rod assembly LH and lock nut.


Hide 45460 18.REMOVE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.