Home › Drivetrain › P810 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › 2020.02–2020.11
RM37A0E _52 Drivetrain _086860 P810 HYBRID TRANSMISSION / TRANSAXLE _0420886 HYBRID VEHICLE TRANSAXLE A

P810 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1.INSTALL TUBE CONNECTOR

HINT:

Perform this procedure only when replacement of the tube connector or O-ring is necessary.


a.

Coat 2 new O-rings with Toyota Genuine ATF WS and install them to the 2 tube connectors.


b.

Using a 19 mm deep socket wrench, install the 2 tube connectors to the hybrid vehicle transaxle assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 30900N 2.INSTALL TRANSAXLE BREATHER PLUG

HINT:

Perform this procedure only when replacement of the transaxle breather plug is necessary.


a.

Install the transaxle breather plug to the hybrid vehicle transaxle assembly.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 3.INSTALL STUD BOLT

a.
C427674

Clean and degrease the 2 stud bolts and 2 stud bolt holes.


b.
C412618C01
1.906,1.615 1.906,1.854 false 1.854,1.865 2.104,2.094 0.25,0.229 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of the 2 stud bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper sealing of the 2 stud bolts, install them within 10 minutes of applying adhesive.



c.

Using a E10 "TORX" socket wrench, install the 2 stud bolts to the hybrid vehicle transaxle assembly.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 4.INSTALL TRANSAXLE HOUSING PLUG

a.

Install the transaxle housing plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 5.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 4 bolts.

C426780N01
1.74,0.781 1.896,0.979 0.156,0.198 10 true A 3.333,1.125 3.49,1.323 0.156,0.198 10 true B 4.76,0.26 4.917,0.458 0.156,0.198 10 true A 5.813,1.229 5.969,1.427 0.156,0.198 10 true A

Torque:
Bolt (A) : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 82125 6.INSTALL TRANSMISSION WIRE

a.

Install the transmission wire to the hybrid vehicle transaxle assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the connector.


Hide G9216 7.INSTALL NO. 3 INVERTER BRACKET

a.
C426778

Install the No. 3 inverter bracket to the hybrid vehicle transaxle assembly with the bolt.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


b.

Install the 5 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 33823 8.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide G1252A 9.INSTALL NO. 2 MOTOR COOLING PIPE

a.
C426775C01
2.271,1.313 2.417,1.313 2.417,1.313 2.521,1.583 false 2.167,1.802 2.385,1.802 false 2.094,1.219 2.406,1.375 0.313,0.156 10 false *1 2,1.719 2.302,1.938 0.302,0.219 10 false *2 0.292,2.063 0.448,2.26 0.156,0.198 10 false A 1.5,2.458 1.656,2.656 0.156,0.198 10 true B
*1 Oil Cooler Union Bolt
*2 Gasket


Temporarily install the No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the oil cooler union bolt and a new gasket.


b.

Temporarily install the bolt (A).


c.

Install the bolt (B).

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


d.

Tighten the bolt (A).

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


e.

Tighten the oil cooler union bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide G125A 10.INSTALL MOTOR COOLING COOLER

a.
C430799N01
1.385,1.792 1.542,1.99 0.156,0.198 10 true 1 1.146,1.052 1.302,1.25 0.156,0.198 10 true 2 2.323,0.646 2.479,0.844 0.156,0.198 10 true 3

Temporarily install the motor cooling cooler to the No. 1 transmission control cable bracket with the 3 bolts.


b.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


c.
C426955C01
1.75,2.344 1.896,2.344 1.896,2.344 2.271,2.583 true 2.927,2.219 2.771,2.219 2.771,2.219 2.646,2.573 true 1.927,3.01 2.167,3.229 0.24,0.219 10 false *a 1.896,2.063 2.188,2.271 0.292,0.208 10 false *b 1.573,2.25 1.813,2.458 0.24,0.208 10 false *c 2.969,2.104 3.271,2.292 0.302,0.188 10 false *d 0.49,2.26 0.75,2.521 0.26,0.26 10 false *f 0.74,2.51 0.927,2.698 0.188,0.188 10 true *e 0.49,2.802 0.75,3.063 0.26,0.26 10 false *f
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Marking
*e Center of Paint Mark
*f 45° (Claw of Clip Location)


Connect the No. 1 motor cooling hose to the tube connector, and slide the clip to secure it.

NOTICE:
·

Make sure to slide the No. 1 motor cooling hose until it contacts the hose stopper of the tube connector.

·

Make sure to align the paint mark of the No. 1 motor cooling hose with the marking of the hybrid vehicle transaxle assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




Hide 30900 12.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
C426771C01
0.406,0.802 0.604,1.01 0.198,0.208 10 true *1 2.583,0.26 2.792,0.469 0.208,0.208 10 true *1
*1 Knock Pin


Make sure that the knock pins are installed to the engine assembly.


b.
C426772

Align the knock pins with the holes in the hybrid vehicle transaxle assembly and, while keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, temporarily install the bolt.

NOTICE:
·

When tightening the bolts, be sure that the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly are in close contact with one another.

·

Do not apply grease to the inner splines of the transmission input damper assembly or input shaft assembly.

·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excessive force when installing the hybrid vehicle transaxle assembly.

·

Make sure to align the hybrid vehicle transaxle assembly so that the input shaft assembly of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper assembly.

·

When inserting the input shaft assembly of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper assembly, do not shake the hybrid vehicle transaxle assembly excessively.

·

When installing the hybrid vehicle transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock pin holes.




c.
C426770N01
2.177,0.354 2.333,0.552 0.156,0.198 10 false A 1.375,0.469 1.531,0.667 0.156,0.198 10 true B 2.99,0.729 3.146,0.927 0.156,0.198 10 false A 0.677,1.594 0.833,1.792 0.156,0.198 10 true C 1.052,2.75 1.208,2.948 0.156,0.198 10 true C 1.615,3.021 1.771,3.219 0.156,0.198 10 false C 2.323,3.083 2.479,3.281 0.156,0.198 10 false D 2.948,2.688 3.104,2.885 0.156,0.198 10 false C

While keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, install the 8 bolts.

Bolt Bolt Length Torque
(A) 50 mm (1.97 in.) 64 N*m (653 kgf*cm, 47 ft.*lbf)
(B), (C) 45 mm (1.77 in.) 46 N*m (469 kgf*cm, 34 ft.*lbf)
(D) 35 mm (1.38 in.) 25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:
·

Bolt (A), (B), (D): Install from the hybrid vehicle transaxle assembly side.

·

Bolt (C): Install from the engine assembly side.




Hide 12303 13.INSTALL REAR ENGINE MOUNTING BRACKET

a.
C426769N01
1.927,1.031 2.083,1.229 0.156,0.198 10 true A 0.792,1.427 0.948,1.625 0.156,0.198 10 true B 1.938,1.469 2.094,1.667 0.156,0.198 10 true C 0.771,1.01 0.927,1.208 0.156,0.198 10 true C

Install the rear engine mounting bracket to the hybrid vehicle transaxle assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (A) → Fully tighten bolt (C)



Hide 12371A 14.INSTALL REAR ENGINE MOUNTING INSULATOR

Hide 12311A 15.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
C426768N01
0.813,0.74 0.969,0.938 0.156,0.198 10 true A 2.344,1.25 2.5,1.448 0.156,0.198 10 true B 0.813,1.104 0.969,1.302 0.156,0.198 10 true C

Install the front engine mounting bracket to the hybrid vehicle transaxle assembly with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A)



Hide 12361A 16.INSTALL FRONT ENGINE MOUNTING INSULATOR

Hide 51100G 17.INSTALL FRONT FRAME ASSEMBLY

Hide 11363A 18.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover to the engine assembly.


Hide 35300B 19.INSTALL OIL PUMP WITH MOTOR ASSEMBLY

Hide G1251B 20.INSTALL NO. 1 MOTOR COOLING PIPE

a.
C430781C01
1.573,0.344 1.833,0.583 0.26,0.24 10 false *a
*a Torque Wrench Fulcrum Length


Temporarily install a new flare nut of the No. 1 motor cooling pipe to the union.


b.

Install the No. 2 oil cooler tube clamp and No. 1 motor cooling pipe to the No. 2 motor cooling pipe with the bolt.

Torque:
8.2 N*m (84 kgf*cm, 73 in.*lbf)


c.

Using a 17 mm union nut wrench, tighten the flare nut to connect the No. 1 motor cooling pipe.

Torque:
Specified Tightening Torque : 34.3 N*m (350 kgf*cm, 25 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

29.4 N*m (300 kgf*cm, 22 ft.*lbf)




Hide 32930G 21.INSTALL NO. 2 TRANSMISSION OIL COOLER HOSE ASSEMBLY

a.

Engage the hose clamp to install the No. 2 transmission oil cooler hose assembly to the No. 2 motor cooling pipe.

C426904C01
1.167,1.031 1.51,0.688 1.51,0.688 1.656,0.688 true 0.427,0.615 0.583,0.615 0.583,0.615 0.771,1.021 true 4.646,1.021 4.427,0.802 4.427,0.802 4.781,1.031 true 4.76,4.979 5.146,4.604 5.146,4.604 4.906,4.979 true 0.708,1.5 0.979,1.75 0.271,0.25 10 false *a 0.719,0.49 1.01,0.688 0.292,0.198 10 false *b 1.719,0.583 2.021,0.802 0.302,0.219 10 false *c 0.24,0.521 0.49,0.76 0.25,0.24 10 false *d 0.229,0.948 0.521,1.167 0.292,0.219 10 false *e 2.063,0.719 2.313,0.948 0.25,0.229 10 false *f 5.396,4.917 5.573,5.146 0.177,0.229 10 true *g 2.063,1.24 2.313,1.469 0.25,0.229 10 false *f 5.021,1.5 5.292,1.75 0.271,0.25 10 false *a 5.083,0.479 5.375,0.677 0.292,0.198 10 false *b 3.865,0.958 4.156,1.177 0.292,0.219 10 false *e 4.25,0.698 4.552,0.917 0.302,0.219 10 false *c 5.688,0.74 5.938,0.969 0.25,0.229 10 false *f 5.688,1.219 5.938,1.448 0.25,0.229 10 false *f 4.313,5.365 4.604,5.563 0.292,0.198 10 false *b 5.208,4.49 5.51,4.708 0.302,0.219 10 false *c
*a 0 to 3 mm (0 to 0.118 in.) *b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark *d Marking
*e Center of Paint Mark *f 45° (Claw of Clip Location)
*g 30° (Center of Clip Location) - -



b.

Connect the No. 2 transmission oil cooler hose assembly to the No. 1 motor cooling pipe and slide the clip to secure it.

NOTICE:
·

Make sure to slide the No. 2 transmission oil cooler hose assembly until it contacts the hose stopper of the No. 1 motor cooling pipe.

·

Make sure to align the paint mark of the No. 2 transmission oil cooler hose assembly with the paint mark of the No. 1 motor cooling pipe.

·

Make sure that the claws of the clip are within the location shown in the illustration.




c.

Connect the No. 2 transmission oil cooler hose assembly to the motor cooling cooler and slide the clip to secure it.

NOTICE:
·

Make sure to slide the No. 2 transmission oil cooler hose assembly until it contacts the hose stopper of the motor cooling cooler.

·

Make sure to align the paint mark of the No. 2 transmission oil cooler hose assembly with the paint mark of the motor cooling cooler.

·

Make sure that the claws of the clip are within the location shown in the illustration.




d.

Connect the No. 2 transmission oil cooler hose assembly to the oil pump with motor assembly and slide the 2 clips to secure it.

NOTICE:
·

Make sure to slide the No. 2 transmission oil cooler hose assembly until it contacts the hose stopper of the oil pump with motor assembly.

·

Make sure to align the paint mark on each No. 2 transmission oil cooler hose assembly with each marking on the oil pump with motor assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




Hide 33185B 22.INSTALL TRANSAXLE UNDER STOPPER BRACKET

a.
C426766N01
1.385,0.292 1.542,0.49 0.156,0.198 10 true A 2.271,1.156 2.427,1.354 0.156,0.198 10 true B 1.188,0.635 1.344,0.833 0.156,0.198 10 true C 2.521,0.844 2.677,1.042 0.156,0.198 10 true C

Install the transaxle under stopper bracket to the hybrid vehicle transaxle assembly with the 4 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A)



Hide 23.CONNECT WATER HOSE

a.

Engage the clamp to connect the water hose.


Hide 821H2 24.CONNECT HV AIR CONDITIONING WIRE

a.

Engage the guide to connect the HV air conditioning wire to the hybrid vehicle transaxle assembly.


b.

Connect the HV air conditioning wire to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 82121 25.CONNECT ENGINE WIRE

a.

Front side:

i.

Connect the engine wire with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



b.

Rear side:

i.

Engage the 6 clamps to connect the engine wire.

C426762


ii.

Connect the engine wire with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Connect the wire harness connector to the rack and pinion power steering gear assembly.

HINT:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.




Hide 45319 26.INSTALL STEERING GEAR HEAT INSULATOR

Hide 28. PERFORM RESOLVER LEARNING

NOTICE:

If the hybrid vehicle transaxle assembly has been replaced, make sure to perform resolver learning.