Home › Drivetrain › P810 (HYBRID TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE
RM37A0E _52 Drivetrain _086860 P810 HYBRID TRANSMISSION / TRANSAXLE _0420889 TRANSMISSION CONTROL CABLE A

P810 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
C332327

·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53295E 3.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 4.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 5.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 82121 6.DISCONNECT ENGINE WIRE

a.
C426965

Rotate the lever while pushing the lock, and disconnect the ECM connector.

NOTICE:

After disconnecting the ECM connector, make sure that dirt, water and other foreign matter does not contact the connecting parts of the ECM connector.



b.

Remove the 2 bolts and disconnect the engine wire.


c.

Disengage the clamp.


Hide 82111 7.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 55446A 9.REMOVE NO. 1 SWITCH HOLE BASE

Hide 55606 10.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 58816B 11.REMOVE FRONT CONSOLE BOX INSERT

Hide 33820B 12.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before removing the transmission control cable assembly, check that the shift lever is in N.


a.
C426819

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


b.
C426820C01
0.365,1.313 0.552,1.521 0.188,0.208 10 true *a
*a Counterclockwise


Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the transmission control cable assembly from the transmission floor shift assembly.


c.
C426967

Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.


d.
C426968

Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with the clip from the No. 1 transmission control cable bracket.


e.
C377870

Using a screwdriver, disengage the 2 claws and remove the clip from the transmission control cable assembly.


f.
C426969

Remove the 2 bolts and disconnect the transmission control cable assembly from the inverter with converter assembly.


g.
C426970

Remove the nut and disconnect the transmission control cable assembly from the vehicle body.


h.
C426971

Remove the 2 nuts and then remove the transmission control cable assembly from the vehicle body.