Home › General › MAINTENANCE › P810 HYBRID TRANSAXLE FLUID
RM37A0E _V1 General _086848 MAINTENANCE _0420902 P810 HYBRID TRANSAXLE FLUID A

MAINTENANCE  P810 HYBRID TRANSAXLE FLUID  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:

For the hybrid transaxle fluid, use Toyota Genuine ATF WS.

Using hybrid transaxle fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transaxle of the vehicle.


PROCEDURE

Hide 53852B 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851D 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51420 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 5.REPLACE HYBRID TRANSAXLE FLUID

HINT:

If no parts have been removed and installed, it is not necessary to start the oil pump with motor assembly (step #9) when replacing the hybrid transaxle fluid, performing a fluid level inspection, etc.


a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.
C426922

Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly. [#2]


c.
C426923

Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the hybrid vehicle transaxle assembly and drain the hybrid transaxle fluid. [#3]


d.

Using a 10 mm hexagon socket wrench, temporarily install the drain plug and gasket to the hybrid vehicle transaxle assembly. [#4]

HINT:

Reuse the old gasket as the drain plug will be removed again.



e.
C426924C01
2.406,1.115 2.521,0.844 2.521,0.844 2.656,0.844 false 2.708,0.729 2.948,0.938 0.24,0.208 10 false *a 3.156,1.708 3.385,1.917 0.229,0.208 10 false *b
*a Filler Nozzle
*b 0 to 10 mm (0 to 0.394 in.)


Add hybrid transaxle fluid until the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. [#5]

NOTICE:
·

Use Toyota Genuine ATF WS.

Using hybrid transaxle fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transaxle of the vehicle.

·

Be sure to fully insert the filler nozzle into the filler plug opening.

·

Be sure to add hybrid transaxle fluid slowly. If hybrid transaxle fluid is added quickly, the hybrid transaxle fluid may hit internal parts and bounce back, resulting in hybrid transaxle fluid coming out of the filler plug opening.

·

Be sure to directly check that the hybrid transaxle fluid level is within the specified range.

·

Driving the vehicle with an insufficient or excessive amount of hybrid transaxle fluid may damage the hybrid vehicle transaxle assembly.




f.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly. [#6]

HINT:

Reuse the old gasket as the filler plug will be removed again.



g.

Lower the vehicle. [#7]


h.

Start the engine. [#8]

i.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


ii.

Idle the engine for 30 seconds with the ignition switch ON (READY).


iii.

Turn the ignition switch off.



i.

Start the oil pump with motor assembly. [#9]

i.

According to the display on the GTS perform the Active Test.

Powertrain > Hybrid Control > Active Test
Tester Display
Control the Motor/Generator Cooling Oil Pump
50004 397 42002
NOTICE:

The active test is not performed when the Duty ratio 50 % or lower or 95 % or higher, or the ambient temperature is 10 °C (50 °F) or lower.



ii.

Start the oil pump with motor assembly and wait for 30 seconds.


iii.

Stop the oil pump with motor assembly.


iv.

Turn the ignition switch off.



j.

Repeat steps [#1] to [#9].


k.

Repeat steps [#1] to [#3].


l.

Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


m.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.

HINT:

Reuse the old gasket as the filler plug will be removed again.



Hide 8.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 51420 9.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53851D 11.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

Hide 53852B 12.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH