47121
1.INSTALL BRAKE PEDAL PAD
Install the brake pedal pad to the brake pedal support assembly.
Installation is easier after applying a small amount of soapy water.
84345
2.INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER
Engage the 2 claws to install the stop light switch mounting adjuster.
47101A
3.INSTALL BRAKE PEDAL RETURN SPRING
|
Up |
|
Front of the Vehicle |
Install the brake pedal return spring to the brake pedal support assembly.
Attach the bottom part of the brake pedal return spring first, making sure that the open part of the hook is facing the front of the vehicle. Attach the top part of the brake pedal return spring second, making sure that the open part of the hook is facing the rear of the vehicle.
4.INSTALL BRAKE PEDAL SUPPORT ASSEMBLY
Push the brake booster with master cylinder toward the engine compartment, and install the brake pedal support assembly while avoiding the stud bolts of the brake booster with master cylinder and brake booster support base.
Be careful not to deform the bracket of the instrument panel reinforcement assembly.
Do not apply excessive force to the brake lines.
Do not apply excessive force to the wire harness.
Return the brake booster with master cylinder to its original position.
Install the brake pedal support assembly with the 4 nuts.
Install the brake pedal support assembly to the instrument panel reinforcement assembly with the bolt.
Engage the 2 clamps to install the wire harness to the brake pedal support assembly.
Connect the connector.
47264A
5.INSTALL PUSH ROD PIN
|
Lithium Soap Base Glycol Grease |
Apply lithium soap base glycol grease to the push rod pin.
Connect the brake master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip as shown in the illustration.
The push rod pin can be installed in either direction.
84340
6.INSTALL STOP LIGHT SWITCH ASSEMBLY
73900
7.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
55446A
8.INSTALL NO. 1 SWITCH HOLE BASE
55045
9.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
53601
10.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
11.CONNECT BRAKE LINE
| *a | Torque Wrench Fulcrum Length |
| *b | Union Nut Wrench |
Using a union nut wrench, connect the brake line to the brake master cylinder sub-assembly.
Do not kink or damage the brake line.
Do not allow the brake line to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
17.4 N*m (177 kgf*cm, 13 ft.*lbf)
| *a | Torque Wrench Fulcrum Length |
| *b | Union Nut Wrench |
Using a union nut wrench, connect the brake line to the brake master cylinder sub-assembly.
Do not kink or damage the brake line.
Do not allow the brake line to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
17.4 N*m (177 kgf*cm, 13 ft.*lbf)
12.CONNECT CONNECTOR
13.BLEED BRAKE SYSTEM
14.INSPECT AND ADJUST BRAKE PEDAL
55606
15.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
62112A
16.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
67914
17.INSTALL FRONT DOOR SCUFF PLATE LH
18.INSPECT SRS WARNING LIGHT