Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for HV Model LHD)
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420929 BRAKE ACTUATOR(for HV Model LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for HV Model LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The parking brake indicator light (red) blinks when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.


a.

Install the 3 brake actuator bracket cushions to the brake actuator bracket assembly.


Hide 44521B 2.INSTALL NO. 2 BRAKE ACTUATOR CASE COLLAR

HINT:

Perform this procedure only when replacement of the No. 2 brake actuator case collars is necessary.


a.

Install the 3 No. 2 brake actuator case collars to the brake actuator bracket cushion.

NOTICE:

Make sure that the No. 2 brake actuator case collar is in full contact with the brake actuator bracket cushion.



b.

Install the 3 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C425437N01
1.875,1.031 2.021,1.229 0.146,0.198 10 true 1 2.646,1.5 2.792,1.667 0.146,0.167 10 true A 2.948,0.865 3.115,1.031 0.167,0.167 10 true 2 2.052,1.5 2.198,1.677 0.146,0.177 10 true 3

Temporarily install the brake actuator assembly to the brake actuator bracket assembly with the bolt (A).


b.

Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts in the order shown in the illustration.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 4.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C426224N01
2.125,3.063 2.281,3.26 0.156,0.198 10 true 1 1.438,3.094 1.594,3.292 0.156,0.198 10 true 2 0.365,0.865 0.5,1.042 0.135,0.177 10 true 3

Temporarily install the brake actuator with bracket with the 2 bolts and nut.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator with bracket by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



b.

Tighten the 2 bolts and nut in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
C426263

Engage the clamp to install a new brake tube clamp.


d.

Return the front brake tube to its original position.

NOTICE:

Do not apply excessive force to the front brake tube.



e.
C425431

Temporarily install the front brake tube to the front flexible hose.

NOTICE:
·

Do not kink or damage the front brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the front brake tube from the connecting parts.




f.
C426261

Engage the clamp to connect the front brake tube.

NOTICE:

Do not kink or damage the front brake tube.



g.
C426225C01
2.125,0.917 2.292,0.417 2.292,0.417 2.875,0.417 true 0.75,1.156 1.583,1.156 true 2.844,0.313 3.031,0.51 0.188,0.198 10 true *b 0.635,1.063 0.813,1.26 0.177,0.198 10 true *a
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly


Temporarily tighten the 2 brake lines to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




h.
C426226C01
2.729,2.865 2.729,2.531 false 1.781,2.813 2.094,3.01 0.313,0.198 10 false *a 2.667,2.875 2.979,3.073 0.313,0.198 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the 2 brake lines.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




i.
C426227C01
1,1.344 1,0.677 true 1.708,1.385 1.708,0.719 true 1.615,0.302 1.365,0.135 1.365,0.135 0.698,0.135 true 2.01,0.396 2.594,0.396 true 0.927,1.354 1.094,1.531 0.167,0.177 10 true *a 1.635,1.406 1.802,1.583 0.167,0.177 10 true *b 0.542,0.042 0.708,0.219 0.167,0.177 10 true *c 2.604,0.313 2.771,0.49 0.167,0.177 10 true *d
*a To Front Wheel Cylinder Assembly RH
*b To Front Wheel Cylinder Assembly LH
*c To Rear Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH


Temporarily tighten the 4 brake lines to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




j.
C426228C01
2.74,2.865 2.74,2.531 false 1.781,2.813 2.094,2.969 0.313,0.156 10 false *a 2.677,2.885 3.01,3.052 0.333,0.167 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the 4 brake lines.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




k.
C425450C01
2.75,3 2.75,2.667 false 1.813,2.938 2.125,3.094 0.313,0.156 10 false *a 2.688,3.01 2.938,3.25 0.25,0.24 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the front brake tube while holding the front flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the front brake tube.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




l.
C426792

Install the brake lines with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


m.
C426229C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 5.CONNECT BRAKE BOOSTER WITH ACCUMULATOR PUMP CONNECTOR

HINT:

Perform this operation only when the accumulator pressure zero down could not be performed using the GTS.


a.
C426232

Connect the brake booster with accumulator pump connector.

NOTICE:

Do not allow water, oil or dirt to enter the connector.



Hide 6.FILL RESERVOIR WITH BRAKE FLUID

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55704B 9.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 10.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 11.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 12.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 13.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 53808A 14.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 15.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 16.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 17.PERFORM INITIALIZATION AND CALIBRATION