Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C004013  Brake Pedal Switch "A" Circuit Open  


DESCRIPTION

The brake pedal load sensing switch (brake pedal support assembly) signal turns on when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU (brake actuator assembly) uses this circuit to detect if the brake pedal is depressed or not.

DTC No. Detection Item DTC Detection Condition Trouble Area
C004013 Brake Pedal Switch "A" Circuit Open When the +BS terminal voltage is from 9.5 to 17.4 V, an open or short in the brake pedal load sensing switch (brake pedal support assembly) continues for 0.3 seconds or more.
·

Brake pedal load sensing switch (brake pedal support assembly)

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C326741E09
2.083,2.167 2.5,2.333 0.417,0.167 10 false A45 2.083,2.333 4.167,2.917 2.083,0.583 10 false Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly) 2.417,1.25 2.948,1.5 0.531,0.25 10 false FSW- 2.167,1.25 2.375,1.458 0.208,0.208 10 false 1 3.615,1.25 4.229,1.458 0.615,0.208 10 false FSW+ 4.167,1.25 4.417,1.5 0.25,0.25 10 false 2 5.5,1.25 5.823,1.448 0.323,0.198 10 false 28 5.76,1.25 6.417,1.458 0.656,0.208 10 false FSW+ 5.25,3 5.583,3.198 0.333,0.198 10 false A39 5.25,3.167 6.771,3.563 1.521,0.396 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY


PROCEDURE

1.READ VALUE USING GTS (BRAKE PEDAL LOAD SENSING SW)
a.

Check that the brake pedal load sensing switch (brake pedal support assembly) display observed on the GTS changes according to brake pedal operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake pedal support assembly) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > Brake/EPB > Data List
Tester Display
Brake Pedal Load Sensing SW
50003 435 61
OK:

The GTS displays OFF / ON according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE PEDAL SUPPORT ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C004013 is not output. A
DTC C004013 is output. B



A

B

4.CHECK HARNESS AND CONNECTOR (BRAKE PEDAL SUPPORT ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A45 brake pedal load sensing switch (brake pedal support assembly) connector.


d.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-2 (FSW+) - A39-28 (FSW+) Always Below 1 Ω
A45-2 (FSW+) or A39-28 (FSW+) - Body ground Always 10 kΩ or higher
A45-1 (FSW-) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL LOAD SENSING SWITCH>ON-VEHICLE INSPECTION

OK:

The brake pedal load sensing switch (brake pedal support assembly) is normal.


Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY