Refer to DTC C050C12.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C050C1F | Left Rear Wheel Speed Sensor Circuit Intermittent | Any of the following is detected:
·
When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more. |
·
Rear skid control sensor LH ·
Rear skid control sensor installation ·
Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
After replacing or removing and installing a skid control sensor, perform Dealer Mode (Signal Check) inspection to confirm that the skid control sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the skid control sensors are operating correctly.
While monitoring the values of the Data List, perform a road test and attempt to reproduce the problem symptoms based on the interview with the customer and the vehicle conditions stored as Freeze Frame Data when the DTC was stored.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Wheel Speed | Rear skid control sensor LH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Speed Open | Rear skid control sensor LH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Tester Display |
|---|
| RL Wheel Speed |
| RL Speed Open |
The values change in accordance with the operation of the vehicle and there is no intermittent operation.
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *1 | Rear Skid Control Sensor LH |
| *a | Correct |
| *b | Incorrect |
| *c | 8.5 N*m (87 kgf*cm, 75 in.*lbf) |
| *d | No clearance |
Turn the ignition switch off.
Check the rear skid control sensor LH installation.
There is no clearance between the rear skid control sensor LH and the rear axle carrier LH.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for 4WD/AWD)>INSTALLATION
Remove the rear skid control sensor LH, and confirm that there is no foreign matter, oil or grease on the rear skid control sensor tip LH.
The rear skid control sensor tip LH is free of oil and foreign matter.
If foreign matter of 1mm x 1mm or more is adhered to the rear skid control sensor LH, this DTC may be stored.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Confirm that there is no foreign matter, oil or grease on the rear speed sensor rotor LH.
The rear speed sensor rotor LH is free of oil and foreign matter.
If foreign matter of 1mm x 1mm or more is adhered to the rear speed sensor rotor LH, this DTC may be stored.
The rear speed sensor rotor LH is incorporated into the rear axle hub and bearing assembly LH.
If the rear speed sensor rotor LH needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
for Rear Skid Control Sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for 4WD/AWD)>REMOVAL
for Rear Speed Sensor Rotor LH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 4WD/AWD)>REMOVAL
NG
Clean the rear speed sensor rotor LH.
Do not use parts cleaner when cleaning the rear speed sensor rotor LH.
| Proceed to |
|---|
| NEXT |
NEXT
While monitoring the values of the Data List, perform a road test and attempt to reproduce the problem symptoms based on the interview with the customer and the vehicle conditions stored as Freeze Frame Data when the DTC was stored.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Wheel Speed | Rear skid control sensor LH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Speed Open | Rear skid control sensor LH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Tester Display |
|---|
| RL Wheel Speed |
| RL Speed Open |
The values change in accordance with the operation of the vehicle and there is no intermittent operation.
Perform the above inspection before removing the sensor and connector.
The rear speed sensor rotor LH is incorporated into the rear axle hub and bearing assembly LH.
If the rear speed sensor rotor LH needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Rear Skid Control Sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for 4WD/AWD)>REMOVAL
for Rear Speed Sensor Rotor LH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 4WD/AWD)>REMOVAL
Clean the rear skid control sensor LH.
When cleaning the rear skid control sensor LH, make sure to clean the installation hole before installation.
| Proceed to |
|---|
| NEXT |
NEXT
While monitoring the values of the Data List, perform a road test and attempt to reproduce the problem symptoms based on the interview with the customer and the vehicle conditions stored as Freeze Frame Data when the DTC was stored.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Wheel Speed | Rear skid control sensor LH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Speed Open | Rear skid control sensor LH open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Tester Display |
|---|
| RL Wheel Speed |
| RL Speed Open |
The values change in accordance with the operation of the vehicle and there is no intermittent operation.
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG