Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C051214  Right Rear Wheel Speed Sensor Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC C051212.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>C051212

DTC No. Detection Item DTC Detection Condition Trouble Area
C051214 Right Rear Wheel Speed Sensor Circuit Short to Ground or Open An open in the skid control sensor signal circuit continues for 0.5 seconds or more.
·

Rear skid control sensor RH

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY

·

After replacing or removing and installing a skid control sensor, perform Dealer Mode (Signal Check) inspection to confirm that the skid control sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Select the line graph display on the GTS.


b.

Check for any momentary interruption in the wire harness and connector.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Normal / Under intermittent Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected
-
Chassis > Brake/EPB > Data List
Tester Display
RR Speed Open
RR Speed Sensor Voltage Open
50003 435 103,112
OK:

Normal (There are no momentary interruptions.)


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
2.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.
C418961C03
0.521,0.167 0.938,0.417 0.417,0.25 2.458,0.167 2.875,0.417 0.417,0.25 2.344,1.719 2.573,1.354 true 0.333,1.75 0.552,1.167 true 3.01,1.729 2.781,1.344 true 1.01,1.75 0.813,1.167 true 0.083,0.083 0.417,0.333 0.333,0.25 10 false *a 0.979,0.208 1.313,0.458 0.333,0.25 10 false *b 2.906,0.208 3.073,0.625 0.167,0.417 10 false *c 0.656,0.208 0.99,0.458 0.333,0.25 10 false u3 2.542,0.208 2.875,0.458 0.333,0.25 10 false uM1 1.031,1.729 1.365,1.979 0.333,0.25 10 false - 0.271,1.74 0.604,1.99 0.333,0.25 10 false + 2.188,1.74 2.521,1.99 0.333,0.25 10 false RR+ 3.01,1.75 3.313,2.083 0.302,0.333 10 false RR-
*a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the u3 and uM1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
u3-1 (+) - uM1-3 (RR+) Always Below 1 Ω
u3-1 (+) or uM1-3 (RR+) - Body ground and other terminals Always 10 kΩ or higher
u3-2 (-) - uM1-4 (RR-) Always Below 1 Ω
u3-2 (-) or uM1-4 (RR-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
uM1-3 (RR+) - A39-20 (RR+) Always Below 1 Ω
uM1-3 (RR+) or A39-20 (RR+) - Body ground Always 10 kΩ or higher
uM1-4 (RR-) - A39-19 (RR-) Always Below 1 Ω
uM1-4 (RR-) or A39-19 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)
a.
C419796C32
1.458,0.167 1.875,0.417 0.417,0.25 1.552,1.24 1.375,1.792 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.583,0.188 1.906,0.375 0.323,0.188 10 false u3 1.323,1.802 1.74,2.052 0.417,0.25 10 false +
*a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
(to Rear Skid Control Sensor RH)


Reconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the uM1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
u3-1 (+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG