Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  Brake Warning Light Remains ON  


DESCRIPTION

This procedure is for troubleshooting when the brake system warning light (red indicator) remains on but no DTCs are output.

The skid control ECU (brake actuator assembly) controls the brake system warning light (red indicator) in the combination meter assembly via CAN communication.

WIRING DIAGRAM

C427356E02
5.667,0.469 5.979,0.667 0.313,0.198 10 false 43 5.677,1.083 5.99,1.281 0.313,0.198 10 false 27 5.969,0.688 6.583,0.885 0.615,0.198 10 false CANL 5.969,1.281 6.583,1.479 0.615,0.198 10 false CANH 5.583,4.583 6.042,4.771 0.458,0.188 10 false A39 5.583,4.75 7.135,5.25 1.552,0.5 10 false Skid Control ECU (Brake Actuator Assembly) 0.75,0.677 1.365,0.875 0.615,0.198 10 false CANL 0.719,1.292 1.333,1.49 0.615,0.198 10 false CANH 1.25,0.479 1.615,0.646 0.365,0.167 10 false 31 0.083,5.875 0.396,6.073 0.313,0.198 10 false H21 0.802,2.604 1.417,2.802 0.615,0.198 10 false VCM 0.885,4.25 1.5,4.448 0.615,0.198 10 false SW 1.25,1.063 1.604,1.229 0.354,0.167 10 false 32 1.25,2.583 1.583,2.833 0.333,0.25 10 false 8 1.25,4.25 1.583,4.448 0.333,0.198 10 false 12 1.906,2.594 2.219,2.792 0.313,0.198 10 false 2 2.094,2.823 2.406,3.021 0.313,0.198 10 false + 2.948,2.833 3.26,3.031 0.313,0.198 10 false E 3.156,2.594 3.469,2.792 0.313,0.198 10 false 1 1.823,4.229 2.135,4.427 0.313,0.198 10 false 1 2.031,4.448 2.344,4.646 0.313,0.198 10 false + 3.552,4.469 3.865,4.667 0.313,0.198 10 false E 3.781,4.24 4.094,4.438 0.313,0.198 10 false 2 1.583,3.083 2.042,3.313 0.458,0.229 10 false A2 1.583,4.833 2.083,5.01 0.5,0.177 10 false A1 1.583,5 4.083,5.5 2.5,0.5 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 1.583,3.25 4.01,3.625 2.427,0.375 10 false Vacuum Warning Switch Assembly 3.938,6.125 5.854,6.49 1.917,0.365 10 false : CAN Communication Line 0.083,6.042 2,6.458 1.917,0.417 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY

·

Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.



PROCEDURE

1.PRE-CHECK
a.

Check that all of the following conditions required for the brake system warning light (red indicator) to turn off are met:

i.

The brake fluid level in the brake master cylinder reservoir assembly is not low.


ii.

The vacuum inside the brake booster decreases.

HINT:

When the vacuum inside the brake booster decreases, the brake system warning light (red indicator) comes on.




Result:
Proceed to
NEXT



NEXT

2.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
2.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.

With a sufficient level of brake fluid, disconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector and confirm that the brake system warning light (red indicator) illuminates.

OK:

The brake system warning light (red indicator) does not turn off.


HINT:

If the brake system warning light (red indicator) turns off, there is a short in the brake fluid level warning switch (brake master cylinder reservoir assembly) circuit.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the H21 combination meter assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-12 (SW) or A1-1 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the H21 combination meter assembly connector.


b.

Reconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


c.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Brake Warning
50004 409 107

d.

Check the combination meter assembly.

OK:

The brake system warning light (red indicator) turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

5.INSPECT VACUUM WARNING SWITCH ASSEMBLY

NG

5.INSPECT VACUUM WARNING SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Inspect the vacuum warning switch assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH>ON-VEHICLE INSPECTION

OK:

The vacuum warning switch assembly is normal.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)

NG

REPLACE VACUUM WARNING SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
a.

Disconnect the A2 vacuum warning switch assembly connector.


b.

Disconnect the H21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-8 (VCM) - A2-2 (+) Always Below 1 Ω
H21-8 (VCM) or A2-2 (+) - Body ground Always 10 kΩ or higher
A2-1 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR