The battery temperature sensors are provided at 6 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the HV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery voltage sensor uses the battery temperature sensors to detect the HV battery temperature, and sends the detected value to the hybrid vehicle control ECU. Based on the results of this detection, the battery voltage sensor controls the blower fan. (The blower fan starts when the HV battery temperature rises above a predetermined level.)
| DTC Title Sensor | Battery Temperature Sensor | GTS Display |
|---|---|---|
| A | 0 | 1 |
| B | 1 | 2 |
| C | 2 | 3 |
| D | 3 | 4 |
| E | 4 | 5 |
| F | 5 | 6 |
Use the reference table above to determine which battery temperature sensor each DTC corresponds to. For example, sensor A in the DTC title column is battery temperature sensor 0. This sensor is displayed as Hybrid Battery Temperature 1 in the Data List.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A9B11 | Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground | The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0A9B15 | Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open | The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0AC511 | Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Ground | The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0AC515 | Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Auxiliary Battery or Open | The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0ACA11 | Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Ground | The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0ACA15 | Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open | The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0AE811 | Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Ground | The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0AE815 | Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Auxiliary Battery or Open | The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0BC211 | Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Ground | The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0BC215 | Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Auxiliary Battery or Open | The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0C3311 | Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Ground | The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| P0C3315 | Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Auxiliary Battery or Open | The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid battery thermistor (battery temperature sensor) ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P0A9B11 | Hybrid Battery Temperature 1 to 6 |
| P0A9B15 | |
| P0AC511 | |
| P0AC515 | |
| P0ACA11 | |
| P0ACA15 | |
| P0AE811 | |
| P0AE815 | |
| P0BC211 | |
| P0BC215 | |
| P0C3311 | |
| P0C3315 |
After checking for the above DTCs, check the hybrid system Data List item "Hybrid Battery Temperature" using the GTS.
| Temperature Displayed | Malfunction |
|---|---|
| Below -45°C (-49°F) | Open or +B short circuit |
| 95°C (203°F) or more | GND short circuit |
If the vehicle is left as is for 24 hours, the value of "Hybrid Battery Temperature" will be almost the same as the ambient temperature.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
With ignition switch ON and wait for 5 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Refer to the wiring diagram for DTC P0A9B2A.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P0A9B2A
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0AFC00, P0AFC96 or P308A12 is not output. | A |
| P0AFC00, P0AFC96 or P308A12 is also output. | B |
Turn the ignition switch off.
A
B
Read the Data List.
| Tester Display |
|---|
| Hybrid Battery Temperature 1 |
| Hybrid Battery Temperature 2 |
| Hybrid Battery Temperature 3 |
| Hybrid Battery Temperature 4 |
| Hybrid Battery Temperature 5 |
| Hybrid Battery Temperature 6 |
A malfunctioning sensor (battery temperature sensor 0, 1, 2, 3, 4 or 5) can be determined by comparing the output temperature of the 6 battery temperature sensors.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery junction block assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL
Check the connections of the z12 battery voltage sensor connector.
The connector is connected securely and there are no contact problems.
| Proceed to |
|---|
| OK |
| NG |
Install the HV battery junction block assembly.
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P0A9B2A
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the upper HV battery cover sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY THERMISTOR>REMOVAL
Check the wire harness and connectors of the battery temperature sensors for abnormalities by sight and touch.
There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.
Install the upper HV battery cover sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG