Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  P0A9B2A  Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range  P0AC52A  Hybrid/EV Battery Temperature Sensor "B" Signal Stuck In Range  P0ACA2A  Hybrid/EV Battery Temperature Sensor "C" Signal Stuck In Range  P0AE82A  Hybrid/EV Battery Temperature Sensor "D" Signal Stuck In Range  P0BC22A  Hybrid/EV Battery Temperature Sensor "E" Signal Stuck In Range  P0C332A  Hybrid/EV Battery Temperature Sensor "F" Signal Stuck In Range  P306562  Hybrid/EV Battery Temperature Sensor "Group 1" Signal Compare Failure  P306A62  Hybrid/EV Battery Temperature Sensor "Group 2" Signal Compare Failure  


DESCRIPTION

Refer to the description for DTC P0A9B11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P0A9B11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A9B2A Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range The performance of battery temperature sensor 0 is abnormal and its output is stuck.
(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0AC52A Hybrid/EV Battery Temperature Sensor "B" Signal Stuck In Range The performance of battery temperature sensor 1 is abnormal and its output is stuck.
(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0ACA2A Hybrid/EV Battery Temperature Sensor "C" Signal Stuck In Range The performance of battery temperature sensor 2 is abnormal and its output is stuck.
(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0AE82A Hybrid/EV Battery Temperature Sensor "D" Signal Stuck In Range The performance of battery temperature sensor 3 is abnormal and its output is stuck.
(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0BC22A Hybrid/EV Battery Temperature Sensor "E" Signal Stuck In Range The performance of battery temperature sensor 4 is abnormal and its output is stuck.
(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0C332A Hybrid/EV Battery Temperature Sensor "F" Signal Stuck In Range The performance of battery temperature sensor 5 is abnormal and its output is stuck.
(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P306562 Hybrid/EV Battery Temperature Sensor "Group 1" Signal Compare Failure The performance of any battery temperature sensor (0 to 2) is abnormal, and the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P306A62 Hybrid/EV Battery Temperature Sensor "Group 2" Signal Compare Failure The performance of any battery temperature sensor (3 to 5) is abnormal, and the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A9B2A Hybrid Battery Temperature 1 to 6
P0AC52A
P0ACA2A
P0AE82A
P0BC22A
P0C332A
P306562
P306A62

HINT:

If the vehicle is left as is for 24 hours, the value of "Hybrid Battery Temperature" will be almost the same as the ambient temperature.


The following items can be helpful when performing repairs:

Data List
·

Vehicle Speed

·

Ambient Temperature


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


P0A9B2A, P0AC52A, P0ACA2A, P0AE82A, P0BC22A, P0C332A:

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the Freeze Frame Data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Temperature 1 to 6" and "Hybrid Battery Current" when ambient temperature is -10°C (14°F) or higher. (These DTCs may not be stored if the vehicle is stopped or being driven at a steady speed.)

HINT:
·

Check that the output of each battery temperature sensor varies.

·

Check that the difference in output between each battery temperature sensor is not excessively large.



7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




P306562, P306A62:

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With ignition switch ON and wait for 10 seconds or more when the ambient temperature is -10°C (14°F) or higher.

HINT:

Check that the difference in output between each battery temperature sensor is not excessively large.


7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A449786E01
2,3.646 2.281,3.813 2.281,3.813 2.615,3.813 true 1.99,1.958 2.271,2.125 2.271,2.125 2.604,2.125 true 1.99,2.75 2.271,2.917 2.271,2.917 2.604,2.917 true 2,4.521 2.281,4.688 2.281,4.688 2.615,4.688 true 2,5.375 2.281,5.542 2.281,5.542 2.615,5.542 true 1.979,6.25 2.26,6.417 2.26,6.417 2.594,6.417 true 1.99,7.104 2.271,7.271 2.271,7.271 2.604,7.271 true 1.375,1.094 1.99,1.292 0.615,0.198 10 false IGCT 0.625,3.719 1.24,3.917 0.615,0.198 10 false IGCT-IG 0.74,5.188 1.313,5.688 0.573,0.5 10 false Auxiliary Battery 1.135,0.75 1.75,0.948 0.615,0.198 10 false 2 1.823,0.385 2.438,0.583 0.615,0.198 10 false 5 1.135,0.385 1.75,0.583 0.615,0.198 10 false 3 1.813,0.75 2.427,0.948 0.615,0.198 10 false 1 2.823,0.75 3.438,0.948 0.615,0.198 10 false 5 2.979,0.833 3.594,1.031 0.615,0.198 10 false MREL 2.563,1.146 3.177,1.344 0.615,0.198 10 false A31 2.563,1.302 4.448,1.74 1.885,0.438 10 false Hybrid Vehicle Control ECU 4.146,0.635 4.948,0.865 0.802,0.229 10 false IGCT NO. 2 4.229,0.385 4.844,0.583 0.615,0.198 10 false 1 4.688,0.385 5.302,0.583 0.615,0.198 10 false 2 5.354,0.281 5.969,0.479 0.615,0.198 10 false 1 5.344,0.458 5.958,0.656 0.615,0.198 10 false y1 5.667,0.479 6.281,0.677 0.615,0.198 10 false IGCT 5.688,1.729 6.302,1.927 0.615,0.198 10 false TC0 5.677,2.208 6.292,2.406 0.615,0.198 10 false GC0 5.677,2.583 6.292,2.781 0.615,0.198 10 false TB0 5.677,3.427 6.292,3.625 0.615,0.198 10 false TB1 5.677,4.292 6.292,4.49 0.615,0.198 10 false TB2 5.677,5.156 6.292,5.354 0.615,0.198 10 false TB3 5.688,6.021 6.302,6.219 0.615,0.198 10 false TB4 5.688,6.885 6.302,7.083 0.615,0.198 10 false TB5 5.667,3.073 6.281,3.271 0.615,0.198 10 false GB0 5.677,3.917 6.292,4.115 0.615,0.198 10 false GB1 5.677,4.781 6.292,4.979 0.615,0.198 10 false GB2 5.677,5.646 6.292,5.844 0.615,0.198 10 false GB3 5.677,6.5 6.292,6.698 0.615,0.198 10 false GB4 5.677,7.375 6.292,7.573 0.615,0.198 10 false GB5 5.667,7.906 6.281,8.104 0.615,0.198 10 false GND 5.354,7.896 5.969,8.094 0.615,0.198 10 false y1 5.302,7.469 5.917,7.667 0.615,0.198 10 false z12 5.313,6.979 5.927,7.177 0.615,0.198 10 false z12 5.313,6.594 5.927,6.792 0.615,0.198 10 false z12 5.302,6.115 5.917,6.313 0.615,0.198 10 false z12 5.313,5.74 5.927,5.938 0.615,0.198 10 false z12 5.313,5.25 5.927,5.448 0.615,0.198 10 false z12 5.302,4.875 5.917,5.073 0.615,0.198 10 false z12 5.302,4.385 5.917,4.583 0.615,0.198 10 false z12 5.302,4.01 5.917,4.208 0.615,0.198 10 false z12 5.313,3.521 5.927,3.719 0.615,0.198 10 false z12 5.302,3.156 5.917,3.354 0.615,0.198 10 false z12 5.302,2.677 5.917,2.875 0.615,0.198 10 false z12 5.302,2.302 5.917,2.5 0.615,0.198 10 false z12 5.292,1.823 5.906,2.021 0.615,0.198 10 false z12 1.427,7.917 2.417,8.365 0.99,0.448 10 false HV Battery 5.365,1.635 5.979,1.833 0.615,0.198 10 false 1 5.333,2.115 5.948,2.313 0.615,0.198 10 false 13 5.333,2.969 5.948,3.167 0.615,0.198 10 false 19 5.333,3.823 5.948,4.021 0.615,0.198 10 false 18 5.333,4.677 5.948,4.875 0.615,0.198 10 false 17 5.333,5.531 5.948,5.729 0.615,0.198 10 false 16 5.333,6.406 5.948,6.604 0.615,0.198 10 false 15 5.333,7.26 5.948,7.458 0.615,0.198 10 false 14 5.375,2.5 5.99,2.698 0.615,0.198 10 false 7 5.375,3.354 5.99,3.552 0.615,0.198 10 false 6 5.375,4.198 5.99,4.396 0.615,0.198 10 false 5 5.375,5.073 5.99,5.271 0.615,0.198 10 false 4 5.375,5.938 5.99,6.135 0.615,0.198 10 false 3 5.385,6.802 6,7 0.615,0.198 10 false 2 2.656,2.042 5.406,2.51 2.75,0.469 10 false Inlet Air Temperature Sensor 2.667,2.833 5.417,3.302 2.75,0.469 10 false Battery Temperature Sensor 0 2.656,3.719 5.406,4.188 2.75,0.469 10 false Battery Temperature Sensor 1 2.667,4.594 5.417,5.063 2.75,0.469 10 false Battery Temperature Sensor 2 2.656,5.458 5.406,5.927 2.75,0.469 10 false Battery Temperature Sensor 3 2.646,6.333 5.396,6.802 2.75,0.469 10 false Battery Temperature Sensor 4 2.646,7.188 5.396,7.656 2.75,0.469 10 false Battery Temperature Sensor 5 5.365,7.719 5.979,7.917 0.615,0.198 10 false 7 5.469,8.302 6.917,8.76 1.448,0.458 10 false Battery Voltage Sensor

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00 or P0AFC96 is not output. A
P0AFC00 or P0AFC96 is also output. B


b.

Turn the ignition switch off.



A

2.CHECK INSTALLATION OF TEMPERATURE SENSOR (HYBRID BATTERY TEMPERATURE SENSOR)

B

2.CHECK INSTALLATION OF TEMPERATURE SENSOR (HYBRID BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper HV battery cover sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY THERMISTOR>REMOVAL


c.

Visually check the installation condition of the relevant battery temperature sensor.

A449758C01
5.031,1.292 5.229,1.49 0.198,0.198 10 true *1 4.271,0.802 4.458,1.01 0.188,0.208 10 true *2 3.479,0.531 3.646,0.708 0.167,0.177 10 true *3 3.25,1.031 3.417,1.229 0.167,0.198 10 true *4 2.563,0.781 2.75,0.99 0.188,0.208 10 true *5 2,0.563 2.188,0.771 0.188,0.208 10 true *6
*1 Battery Temperature Sensor 0 *2 Battery Temperature Sensor 1
*3 Battery Temperature Sensor 2 *4 Battery Temperature Sensor 3
*5 Battery Temperature Sensor 4 *6 Battery Temperature Sensor 5


Standard Condition:

Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely.



Result:
Result Proceed to
Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely. A
Claws are damaged. B
Any of battery temperature sensors are not installed correctly, but claws are not damaged. C


d.

Install the upper HV battery cover sub-assembly.



A

3.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

B

C

INSTALL PARTS CORRECTLY

3.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.

Disconnect the z12 battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A449759C01
0.5,2.115 0.917,2.344 0.417,0.229 1.656,2.281 0.99,2.625 true 1,1.854 1.625,2.188 true 1.708,2.281 1.073,2.948 true 1.177,1.594 1.719,2.188 true 1.479,1.5 1.781,2.167 true 1.792,2.281 1.458,3.063 true 1.813,1.479 1.865,2.177 true 1.865,2.281 1.906,3.073 true 2.219,1.583 1.938,2.188 true 2.417,1.917 2.021,2.177 true 2.417,2.531 2.01,2.281 true 1.938,2.271 2.313,2.917 true 0.615,2.156 1.042,2.479 0.427,0.323 10 false z12 0.74,1.75 1.063,2.021 0.323,0.271 10 false TB0 0.927,1.479 1.25,1.708 0.323,0.229 10 false TB1 1.313,1.333 1.646,1.542 0.333,0.208 10 false TB2 1.292,3.083 1.646,3.292 0.354,0.208 10 false GB2 0.802,2.927 1.188,3.115 0.385,0.188 10 false GB1 0.688,2.563 1.063,2.75 0.375,0.188 10 false GB0 0.094,0.042 0.563,0.469 0.469,0.427 10 false *a 1.781,3.104 2.135,3.313 0.354,0.208 10 false GB3 1.688,1.313 2.021,1.521 0.333,0.208 10 false TB3 2.115,1.417 2.448,1.625 0.333,0.208 10 false TB4 2.448,1.823 2.781,2.031 0.333,0.208 10 false TB5 2.448,2.49 2.802,2.698 0.354,0.208 10 false GB5 2.24,2.938 2.594,3.146 0.354,0.208 10 false GB4
*a Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 5).

Tester Connection:
Tester Connection Battery Temperature Sensor
z12-7 (TB0) - z12-19 (GB0) 0
z12-6 (TB1) - z12-18 (GB1) 1
z12-5 (TB2) - z12-17 (GB2) 2
z12-4 (TB3) - z12-16 (GB3) 3
z12-3 (TB4) - z12-15 (GB4) 4
z12-2 (TB5) - z12-14 (GB5) 5


Standard Resistance:
Thermistor Temperature Condition Specified Condition
0 to 10°C (32 to 50°F) Ignition switch off 17.7 to 27.8 kΩ
10 to 20°C (50 to 68°F) Ignition switch off 12.0 to 18.2 kΩ
20 to 30°C (68 to 86°F) Ignition switch off 8.22 to 12.2 kΩ
30 to 40°C (86 to 104°F) Ignition switch off 5.74 to 8.41 kΩ
40 to 50°C (104 to 122°F) Ignition switch off 4.09 to 5.91 kΩ


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



e.

Disconnect the y1 battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



f.
A449760C01
0.24,2.094 0.646,2.333 0.406,0.24 2.813,2.083 3.219,2.323 0.406,0.24 1.708,2.198 2,1.76 true 2.042,2.729 1.719,2.292 true 2.594,2.167 2.813,1.708 true 2.833,2.698 2.604,2.24 true 1.625,2.177 1.885,1.49 true 1.552,2.188 1.583,1.417 true 1.469,2.167 1.302,1.479 true 1.396,2.188 1.042,1.521 true 1.323,2.188 0.781,1.552 true 1.24,2.188 0.656,1.75 true 1.948,3 1.635,2.281 true 1.698,3.146 1.542,2.271 true 1.385,3.188 1.49,2.281 true 1.021,3.115 1.406,2.271 true 0.771,2.99 1.323,2.271 true 0.604,2.792 1.25,2.271 true 1.927,1.604 2.385,1.802 0.458,0.198 10 false TC0 0.896,1.354 1.354,1.552 0.458,0.198 10 false TB2 0.604,1.375 1.063,1.573 0.458,0.198 10 false TB1 0.396,1.646 0.854,1.844 0.458,0.198 10 false TB0 1.958,2.75 2.417,2.948 0.458,0.198 10 false GC0 0.875,3.135 1.333,3.333 0.458,0.198 10 false GB2 0.573,3 1.031,3.208 0.458,0.208 10 false GB1 0.313,2.74 0.771,2.948 0.458,0.208 10 false GB0 2.708,1.542 3.198,1.865 0.49,0.323 10 false IGCT 2.729,2.719 3.188,2.917 0.458,0.198 10 false GND 0.344,2.135 0.719,2.49 0.375,0.354 10 false z12 2.948,2.125 3.323,2.479 0.375,0.354 10 false y1 0.115,0.021 0.573,0.219 0.458,0.198 10 false *a 1.792,1.333 2.25,1.531 0.458,0.198 10 false TB5 1.479,1.26 1.938,1.458 0.458,0.198 10 false TB4 1.177,1.323 1.635,1.521 0.458,0.198 10 false TB3 1.854,3 2.313,3.198 0.458,0.198 10 false GB5 1.594,3.167 2.052,3.365 0.458,0.198 10 false GB4 1.24,3.208 1.698,3.406 0.458,0.198 10 false GB3
*a Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-7 (TB0) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-7 (TB0) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-19 (GB0) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-19 (GB0) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-6 (TB1) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-6 (TB1) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-18 (GB1) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-18 (GB1) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-5 (TB2) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-5 (TB2) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-17 (GB2) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-17 (GB2) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-4 (TB3) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-4 (TB3) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-16 (GB3) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-16 (GB3) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-3 (TB4) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-3 (TB4) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-15 (GB4) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-15 (GB4) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-2 (TB5) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-2 (TB5) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-14 (GB5) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-14 (GB5) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-1 (TC0) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-1 (TC0) - y1-7 (GND) Ignition switch off 10 kΩ or higher
z12-13 (GC0) - y1-1 (IGCT) Ignition switch off 10 kΩ or higher
z12-13 (GC0) - y1-7 (GND) Ignition switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



g.

Reconnect the y1 and z12 battery voltage sensor connectors.


h.

Install the HV battery junction block assembly.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
4.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper HV battery cover sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY THERMISTOR>REMOVAL


c.

Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.

Specified Condition:

There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.



d.

Install the upper HV battery cover sub-assembly.


Result:
Proceed to
OK
NG



OK

NG

REPAIR HARNESS OR CONNECTOR (BATTERY TEMPERATURE SENSOR)