Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  P1C8549  High Voltage Power Resource Internal Electronic Failure  


DESCRIPTION

The hybrid vehicle control ECU monitors the system internal operation, and it will store a DTC and perform fail-safe control if it detects the following malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C8549 High Voltage Power Resource Internal Electronic Failure Battery overcurrent or overload current occurs due to a malfunction in the high-voltage circuit between the hybrid system, HV battery and inverter.
(1 trip detection logic)
·

Hybrid vehicle control ECU

·

Battery voltage sensor

·

HV battery junction block assembly

·

Hybrid battery thermistor (wire harness or connector)

·

Wire harness or connector


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P1C8549
·

Hybrid Battery Current

·

Hybrid Battery Voltage

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the Freeze Frame Data items "Vehicle Speed", "Accelerator Position" and "Hybrid Battery Current".

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C45
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

If the DTCs are cleared or the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal before performing repairs, turning the ignition switch to ON (READY) may cause a malfunction. Do not turn the ignition switch to ON (READY).



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P1C8549 only is output. A
DTCs other than P1C8549 is also output. B



b.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (HYBRID BATTERY CURRENT)

B

2.READ VALUE USING GTS (HYBRID BATTERY CURRENT)
a.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Current
50003 397 228
Result:
Result Proceed to
The value of Hybrid Battery Current is between -4 A and 4 A A
Other than above B



b.

Turn the ignition switch off.



A

B

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A449763N01
1.656,1.094 2.031,1.354 0.375,0.26 1.677,1.115 2,1.323 0.323,0.208 10 true z13

Disconnect the z13 battery current sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



c.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


d.
A449756N01
1.083,0.958 1.438,1.219 0.354,0.26 1.115,0.979 1.396,1.188 0.281,0.208 10 true z12

Disconnect the z12 battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A449771C01
2.323,1.938 2.75,2.198 0.427,0.26 2.188,3.76 2.552,3.99 0.365,0.229 1.146,1.563 1.552,2.042 true 1.885,4.031 2.135,4.396 true 0.823,2.396 1.469,2.146 true 0.823,1.875 1.469,2.052 true 1.333,4.417 1.563,4.042 true 1.073,3.76 1.563,3.802 true 0.229,0.073 0.677,0.552 0.448,0.479 10 false *a 0.74,3.042 1.313,3.573 0.573,0.531 10 false *b 2.427,1.99 2.875,2.469 0.448,0.479 10 false z12 2.25,3.802 2.563,4.021 0.313,0.219 10 false z13 0.938,1.438 1.313,1.656 0.375,0.219 10 false IB0 2.104,4.427 2.438,4.615 0.333,0.188 10 false IB0 0.573,2.333 0.906,2.531 0.333,0.198 10 false GIB 0.583,1.771 0.906,2.021 0.323,0.25 10 false VIB 1.188,4.438 1.5,4.625 0.313,0.188 10 false GIB 0.833,3.677 1.188,3.938 0.354,0.26 10 false VIB
*a Rear view of wire harness connector
(to Battery Voltage Sensor)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z12-9 (IB0) - z13-4 (IB0) Ignition switch off Below 1 Ω
z12-22 (GIB) - z13-3 (GIB) Ignition switch off Below 1 Ω
z12-10 (VIB) - z13-1 (VIB) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z12-9 (IB0) or z13-4 (IB0) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-22 (GIB) or z13-3 (GIB) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-10 (VIB) or z13-1 (VIB) - Body ground and other terminals Ignition switch off 10 kΩ or higher



f.

Reconnect the z12 battery voltage sensor connector.


g.

Install the HV battery junction block assembly.


h.

Reconnect the z13 battery current sensor connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))

NG

REPLACE HYBRID BATTERY THERMISTOR (WIRE HARNESS OR CONNECTOR)

4.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A449763N01
1.656,1.094 2.031,1.354 0.375,0.26 1.677,1.115 2,1.323 0.323,0.208 10 true z13

Disconnect the z13 battery current sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



c.

Remove the HV battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


d.

Connect the z13 battery current sensor connector.


e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the ignition switch to ON.


g.
A449753C02
1.49,0.323 1.844,0.521 0.354,0.198 1.729,1.698 1.448,1.031 true 1.448,0.938 0.958,1.708 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.563,0.344 1.958,0.656 0.396,0.313 10 false z12 1.635,1.719 1.969,1.979 0.333,0.26 10 false GIB 0.823,1.719 1.156,1.979 0.333,0.26 10 false VIB
*a Component with harness connected
(Battery Voltage Sensor)


Using a Toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.

Tester Connection Switch Condition
z12-10 (VIB) - z12-22 (GIB) Ignition switch ON

NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Be sure to set the Toyota electrical tester to 40 V when performing this test.




h.
A449753C03
1.479,0.25 1.885,0.458 0.406,0.208 1.208,1.729 1.448,1.01 true 1.521,0.948 1.802,1.74 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.573,0.271 1.969,0.583 0.396,0.313 10 false z12 1.063,1.76 1.396,2.021 0.333,0.26 10 false GIB 1.74,1.75 2.073,2.01 0.333,0.26 10 false IB0
*a Component with harness connected
(Battery Voltage Sensor)


Using a Toyota electrical tester set to 4 V, measure the IB0 voltage according to the value(s) in the table below.

Tester Connection Switch Condition
z12-9 (IB0) - z12-22 (GIB) Ignition switch ON

NOTICE:

Be sure to set the Toyota electrical tester to 4 V when performing this test.



i.

Compare the measured values of the IB0 terminal voltage and VIB terminal voltage using the following formula:

IB0 voltage - VIB Voltage / 2 = less than 0.081 V
IB0 voltage - VIB Voltage / 2 = -0.081 V or higher


Result:
Result Proceed to
Within the specified range above A
Other than above B


j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.


l.

Install the HV battery junction block assembly.


HINT:

When the ignition switch is ON, the actual current will be approximately 0 A. The following graph shows the relation of the actual output voltage between the battery current sensor terminal IB0 and the actual current used for DTC judgment.

A382906E18
1.708,0.281 2.625,0.729 0.917,0.448 10 false Voltage 4.844,2.188 5.865,2.698 1.021,0.51 10 false Current 1.583,1.219 2.5,1.667 0.917,0.448 10 false VIB/2 3.177,2.656 4.094,3.104 0.917,0.448 10 false -4 A 3.896,2.656 4.813,3.115 0.917,0.458 10 false +4 A 3.563,2.656 4.479,3.104 0.917,0.448 10 false 0 A 0.635,2.781 3.625,3.021 2.99,0.24 10 false Battery Current Sensor Normal Range 0.625,3.063 3.615,3.302 2.99,0.24 10 false Toyota electrical tester margin of error 0.635,3.333 3.646,3.635 3.01,0.302 10 false Battery current sensor operation malfunction



A

5.REPLACE BATTERY VOLTAGE SENSOR

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

5.REPLACE BATTERY VOLTAGE SENSOR

NEXT

6.SIMULATION TEST
6.SIMULATION TEST
a.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

b.

Drive the vehicle on urban roads for approximately 10 minutes.


c.

Turn the ignition switch off and wait for 2 minutes or more.


d.

Turn the ignition switch to ON and wait for 30 seconds or more.


Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
7.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
a.

Read output DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
P1C8549 is output B



b.

Turn the ignition switch off.



A

END

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY