Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  P314A31  Motor Electronics Coolant Pump "A" No Signal  


DESCRIPTION

Refer to the description for DTC P0C7396.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>P0C7396

The inverter water pump assembly sends the inverter water pump speed (measured value) signal to the hybrid vehicle control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P314A31 Motor Electronics Coolant Pump "A" No Signal The inverter water pump speed signal is not sent to the hybrid vehicle control ECU when the ignition switch is turned to ON (READY).*
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Inverter water pump assembly

·

INV W/PMP fuse

·

IGCT NO. 2 fuse

·

INV W/PMP relay


Comes on Master Warning:
Comes on

*: Any of the following conditions is met.
·

A malfunction (open, short to +B or short to ground) in the speed signal line from the inverter water pump assembly to the hybrid vehicle control ECU is detected.

·

A malfunction in the +B line is detected.

·

A malfunction in the inverter water pump assembly power source circuit is detected.

·

A malfunction in hybrid vehicle control ECU power source circuit is detected.


Related Data List
DTC No. Data List
P314A31
·

Inverter Water Pump Revolution

·

Inverter Water Pump Duty Ratio

·

Ready Signal



Related Active Test
DTC No. Active Test
P314A31 Activate the Inverter Water Pump

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Turn the ignition switch to ON (READY) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

PROCEDURE

1.CLEAR DTC
a.

Read and record the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Trouble Codes
50001 397

b.

Clear the DTCs and Freeze Frame Data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

c.

Turn the ignition switch off and wait for 2 minutes or more.


Result:
Proceed to
NEXT



NEXT

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
·

Make sure that the HV coolant level is above the low line of the inverter reserve tank.

·

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.



HINT:
·

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.

·

When the inverter water pump assembly signal line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.



a.

Perform the "Activate the Inverter Water Pump" Active Test.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Inverter Water Pump
50004 397 1

b.

Touch the inverter water pump assembly and check that it is operating (vibrating).

OK:

The inverter water pump is operating (vibrating).


HINT:

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.

Disconnect the A56 inverter water pump assembly connector.


c.
C408032C07
1.448,0.26 1.896,0.531 0.448,0.271 0.375,3.313 0.823,3.583 0.448,0.271 1.042,4.031 1.552,3.531 true 2.563,2.135 2.375,1.594 true 0.073,0.115 0.385,0.313 0.313,0.198 10 false *a 0.094,2.885 0.406,3.083 0.313,0.198 10 false *b 1.542,0.313 1.854,0.51 0.313,0.198 10 false A31 0.479,3.375 0.792,3.573 0.313,0.198 10 false A56 0.844,4.115 1.365,4.323 0.521,0.208 10 false NWP 2.427,2.188 2.948,2.396 0.521,0.208 10 false NIWP
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A31-33 (NIWP) - A56-2 (NWP) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A31-33 (NIWP) or A56-2 (NWP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


HINT:

Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.



d.

Reconnect the A56 inverter water pump assembly connector.


e.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect the A56 inverter water pump assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

C407546C89
5.313,0.302 5.656,0.552 0.344,0.25 1.542,0.396 1.885,0.646 0.344,0.25 6.021,1.302 6.406,2.302 true 1.24,1.469 0.958,2.25 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 5.385,0.354 5.844,0.552 0.458,0.198 10 false H67 6.385,2.344 6.885,2.542 0.5,0.198 10 false E1 0.792,2.302 1.292,2.5 0.5,0.198 10 false NIWP 1.604,0.438 2.063,0.635 0.458,0.198 10 false A31
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A31-33 (NIWP) - H67-3 (E1) Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Reconnect the A56 inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

7.CLEAR DTC

NEXT

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Perform the "Activate the Inverter Water Pump" Active Test.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Inverter Water Pump
50004 397 1

b.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.

A368673C16
1.385,0.177 1.792,0.438 0.406,0.26 5.333,0.177 5.698,0.448 0.365,0.271 5.896,2.01 5.969,1.146 true 0.938,2.063 1.188,1.333 true 4.573,3.073 5.083,3.344 0.51,0.271 10 false GND 5.802,2.052 6.313,2.323 0.51,0.271 10 false E1 0.76,2.115 1.271,2.385 0.51,0.271 10 false NIWP 1.469,0.229 1.979,0.5 0.51,0.271 10 false A31 5.406,0.24 5.917,0.51 0.51,0.271 10 false H67 0.135,0.146 0.646,0.417 0.51,0.271 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Item Content
Terminal A31-33 (NIWP) - H67-3 (E1)
Equipment Setting 5 V/DIV., 5 ms./DIV.
Condition Ignition switch ON, during Active Test

OK:

The period of the wavelength is 13 msec or less.



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

15.REPLACE INVERTER WATER PUMP ASSEMBLY
9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

10.CHECK INSTALLATION CONDITION (INV W/PMP RELAY)

NG

CONNECT SECURELY (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

10.CHECK INSTALLATION CONDITION (INV W/PMP RELAY)
a.
A449795C01
1.531,0.958 0.688,1.927 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 0.542,1.927 0.854,2.083 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay


Check installation condition of the INV W/PMP relay.

OK:

INV W/PMP relay is installed correctly.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (IGCT RELAY - INV W/PMP RELAY)

NG

17.INSPECT RELAY (INV W/PMP)
11.CHECK HARNESS AND CONNECTOR (IGCT RELAY - INV W/PMP RELAY)
a.
A443452C01
0.25,0.177 0.563,0.375 0.313,0.198 10 false *1 0.646,1.771 0.958,1.969 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT Relay Holder


Remove the IGCT relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.
A449788C01
0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 0.333,1.24 0.646,1.438 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay Holder


Remove the INV W/PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.
A288054C11
0.177,0.177 0.49,0.375 0.313,0.198 10 *a 0.99,1.385 1.302,1.583 0.313,0.198 10 *b 2.021,2.979 2.333,3.177 0.313,0.198 10 *c
*a Example
*b Shake Slightly
*c Vibrate Slightly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT relay holder) - 1 (INV W/PMP relay holder) Ignition switch off Below 1 Ω


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.


HINT:
·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly

Apply slight vibration with a finger to the No. 5 floor relay block and No. 5 floor junction block assembly and check whether a malfunction occurs.

·

No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly

Apply slight vibration with a finger to the No. 1 engine room relay block and No. 1 junction block assembly and check whether a malfunction occurs.

·

IGCT NO. 2 fuse

Apply slight vibration with a finger to the IGCT NO. 2 fuse and check whether a malfunction occurs.




d.

Install the IGCT relay and INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

12.INSPECT RELAY (INV W/PMP)

NG

18.CHECK INSTALLATION CONDITION (IGCT NO. 2 FUSE)
12.INSPECT RELAY (INV W/PMP)
a.
A449795C01
1.531,0.958 0.688,1.927 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 0.542,1.927 0.854,2.083 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.
A167865C11
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

NG

20.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
13.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
A407400C24
1.542,0.354 2,0.625 0.458,0.271 2.469,1.667 2.073,1.156 true 2.427,1.74 2.885,1.938 0.458,0.198 10 false +BWP 1.646,0.417 2.104,0.615 0.458,0.198 10 false A56 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


A288054C11
0.177,0.177 0.49,0.375 0.313,0.198 10 *a 0.99,1.385 1.302,1.583 0.313,0.198 10 *b 2.021,2.979 2.333,3.177 0.313,0.198 10 *c
*a Example
*b Shake Slightly
*c Vibrate Slightly


a.

Disconnect the A56 inverter water pump assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A56-4 (+BWP) - Body ground Ignition switch ON 11 to 14 V


NOTICE:
·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.

·

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.



HINT:
·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly

Apply slight vibration with a finger to the No. 1 engine room relay block and No. 1 junction block assembly and check whether a malfunction occurs.

·

INV W/PMP fuse

Apply slight vibration with a finger to the INV W/PMP fuse and check whether a malfunction occurs.

·

INV W/PMP Relay

Apply slight vibration with a finger to the INV W/PMP relay and check whether a malfunction occurs.




d.

Turn the ignition switch off.


e.

Reconnect the A56 inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

NG

21.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
14.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the A56 inverter water pump assembly connector.


b.
A407400C25
1.542,0.354 2,0.625 0.458,0.271 0.958,1.552 1.375,1.135 true 0.635,1.615 1.094,1.813 0.458,0.198 10 false GND 1.656,0.417 2.115,0.615 0.458,0.198 10 false A56 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-1 (GND) - Body ground Ignition switch off Below 1 Ω



c.

Reconnect the A56 inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

15.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

16.ADD HV COOLANT AND PERFORM AIR BLEEDING
16.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

END

17.INSPECT RELAY (INV W/PMP)
a.
A449795C01
1.531,0.958 0.688,1.927 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 0.542,1.927 0.854,2.083 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.
A167865C11
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

CONNECT SECURELY (INV W/PMP RELAY)

NG

REPLACE RELAY (INV W/PMP)

18.CHECK INSTALLATION CONDITION (IGCT NO. 2 FUSE)
a.
A449796C01
0.896,1.24 1.875,0.885 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 0.729,1.177 1.042,1.375 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT NO. 2 Fuse


Check installation condition of the IGCT NO. 2 fuse.

OK:

IGCT NO. 2 fuse is installed correctly.



Result:
Proceed to
OK
NG



OK

19.CHECK FUSE (IGCT NO. 2)

NG

25.INSPECT RELAY (INV W/PMP)
19.CHECK FUSE (IGCT NO. 2)
a.
A449796C01
0.896,1.24 1.875,0.885 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 0.729,1.177 1.042,1.375 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT NO. 2 Fuse


Remove the IGCT NO. 2 fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 2 fuse Always Below 1 Ω



c.

Install the IGCT NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 2 FUSE HOLDER TERMINAL)

NG

26.CHECK FUSE HOLDER TERMINAL (IGCT NO. 2 FUSE)
20.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
a.
A449795C01
1.531,0.958 0.688,1.927 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 0.542,1.927 0.854,2.083 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay


Check the terminals of the INV W/PMP relay holder.

OK:

The terminals of the INV W/PMP relay holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

REPLACE RELAY (INV W/PMP)

NG

27.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
21.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
a.
A449764C01
2,1.698 2.604,2.458 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *1 2.635,2.458 2.948,2.656 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Fuse


Check installation condition of the INV W/PMP fuse.

OK:

INV W/PMP fuse is installed correctly.



Result:
Proceed to
OK
NG



OK

22.INSPECT RELAY (INV W/PMP)

NG

CONNECT SECURELY (INV W/PMP FUSE)

22.INSPECT RELAY (INV W/PMP)
a.
A449795C01
1.531,0.958 0.688,1.927 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 0.542,1.927 0.854,2.083 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.
A167865C11
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)

NG

32.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
23.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)
a.

Remove the INV W/PMP relay and INV W/PMP fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the A56 inverter water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

A449797C01
0.438,1.25 0.833,1.521 0.396,0.271 2.177,2.063 1.99,1.375 true 4.521,0.125 4.833,0.323 0.313,0.198 10 false *1 3.823,0.479 4.135,0.677 0.313,0.198 10 false *2 3.792,1.729 4.104,1.927 0.313,0.198 10 false *3 0.667,0.646 0.979,0.844 0.313,0.198 10 false *a 1.979,2.104 2.542,2.406 0.563,0.302 10 false +BWP 0.51,1.302 1.073,1.604 0.563,0.302 10 false A56
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly *2 INV W/PMP Relay Holder
*3 INV W/PMP Fuse - -
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A56-4 (+BWP) - 3 (INV W/PMP relay holder) Ignition switch off Below 1 Ω
2 (INV W/PMP fuse holder) or A56-4 (+BWP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.



d.

Reconnect the A56 inverter water pump assembly connector.


e.

Install the INV W/PMP relay and INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

24.CHECK FUSE (INV W/PMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK FUSE (INV W/PMP)
a.
A449764C01
2,1.698 2.604,2.458 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *1 2.635,2.458 2.948,2.656 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL OR INV W/PMP RELAY HOLDER TERMINAL)

NG

28.REPLACE INVERTER WATER PUMP ASSEMBLY
25.INSPECT RELAY (INV W/PMP)
a.
A449795C01
1.531,0.958 0.688,1.927 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 0.542,1.927 0.854,2.083 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.
A167865C11
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

CONNECT SECURELY (IGCT NO. 2 FUSE)

NG

30.REPLACE RELAY (INV W/PMP)
26.CHECK FUSE HOLDER TERMINAL (IGCT NO. 2 FUSE)
a.
A449796C01
0.896,1.24 1.875,0.885 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 0.729,1.177 1.042,1.375 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT NO. 2 Fuse


Check the terminals of the IGCT NO. 2 fuse holder.

OK:

The terminals of the IGCT NO. 2 fuse holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

REPLACE FUSE (IGCT NO. 2)

NG

31.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 2 FUSE HOLDER TERMINAL)
27.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
a.

Repair or replace the terminals of the INV W/PMP relay holder.


Result:
Proceed to
NEXT



NEXT

REPLACE RELAY (INV W/PMP)

28.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

29.ADD HV COOLANT AND PERFORM AIR BLEEDING
29.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP)

30.REPLACE RELAY (INV W/PMP)
Result:
Proceed to
NEXT



NEXT

CONNECT SECURELY (IGCT NO. 2 FUSE)

31.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 2 FUSE HOLDER TERMINAL)
a.

Repair or replace the terminals of the IGCT NO. 2 fuse holder.


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 2)

32.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
a.
A449795C01
1.531,0.958 0.688,1.927 true 0.146,0.063 0.458,0.219 0.313,0.156 10 false *1 0.542,1.927 0.854,2.083 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay


Check the terminals of the INV W/PMP relay holder.

OK:

The terminals of the INV W/PMP relay holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

33.CHECK FUSE (IGCT NO. 2)

NG

34.CHECK FUSE (IGCT NO. 2)
33.CHECK FUSE (IGCT NO. 2)
a.
A449796C01
0.896,1.24 1.875,0.885 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 0.729,1.177 1.042,1.375 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT NO. 2 Fuse


Remove the IGCT NO. 2 fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 2 fuse Always Below 1 Ω



c.

Install the IGCT NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

REPLACE RELAY (INV W/PMP)

NG

36.REPLACE RELAY (INV W/PMP)
34.CHECK FUSE (IGCT NO. 2)
a.
A449796C01
0.896,1.24 1.875,0.885 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 0.729,1.177 1.042,1.375 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT NO. 2 Fuse


Remove the IGCT NO. 2 fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 2 fuse Always Below 1 Ω



c.

Install the IGCT NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

35.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)

NG

37.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
35.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
a.

Repair or replace the terminals of the INV W/PMP relay holder.


Result:
Proceed to
NEXT



NEXT

REPLACE RELAY (INV W/PMP)

36.REPLACE RELAY (INV W/PMP)
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 2)

37.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
a.

Repair or replace the terminals of the INV W/PMP relay holder.


Result:
Proceed to
NEXT



NEXT

38.REPLACE RELAY (INV W/PMP)
38.REPLACE RELAY (INV W/PMP)
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 2)