Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  Pattern Select Switch EV Mode Circuit  


DESCRIPTION

The EV drive mode switch signal will be sent to the hybrid vehicle control ECU when the EV drive mode switch is operated. If the specified conditions are met, the system enters EV drive mode and the vehicle will be driven using EV drive mode. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter assembly to illuminate the EV drive mode indicator.

WIRING DIAGRAM

A376617E53
1.49,1.25 3.438,1.563 1.948,0.313 10 false Combination Meter Assembly 2.125,1.896 2.875,2.156 0.75,0.26 10 false EV MODE 1.385,2.854 3.75,3.281 2.365,0.427 10 false EV Drive Mode Switch (Pattern Select Switch Assembly) 4.708,2.958 6.719,3.427 2.01,0.469 10 false Hybrid Vehicle Control ECU 5.104,2.063 5.688,2.323 0.583,0.26 10 false EVSW 4.802,2.063 5.083,2.344 0.281,0.281 10 false 33 4.708,2.771 4.99,3.052 0.281,0.281 10 false H67 1.385,2.667 1.667,2.948 0.281,0.281 10 false P9 5.76,1.635 6.042,1.917 0.281,0.281 10 false +B 1.5,2.063 1.781,2.344 0.281,0.281 10 false 2 1.771,2.063 2.24,2.375 0.469,0.313 10 false E 3,2.073 3.281,2.354 0.281,0.281 10 false S 3.208,2.073 3.49,2.354 0.281,0.281 10 false 5 0.583,3.385 2.531,3.698 1.948,0.313 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

Depending on the condition of the hybrid control system and the driving conditions, the drive mode may not be able to be changed to EV drive mode and a warning message will be displayed on the multi-information display.

HINT:

Under the following principal conditions, the drive mode will not be able to be changed to EV drive mode:

·

The hybrid control system is extremely hot.

·

The hybrid control system is extremely cold.

·

The engine is warming up.

·

The SOC (State of Charge) of the HV battery is low.

·

The vehicle is being driven at a speed higher than the specified value.

·

The accelerator pedal is being fully depressed or the vehicle is climbing a slope.

·

The defroster is on.

·

DTCs are stored.



PROCEDURE

1.ASK ABOUT VEHICLE CONDITION
a.

Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV drive mode.

Result:
Result Proceed to
No buzzer sounded and no message was displayed on multi-information display A
A buzzer sounded and a message was displayed on multi-information display B


HINT:

If a buzzer sounds or a message is displayed on the multi-information display, one or more of the EV drive mode entry conditions have not been met.




A

2.READ VALUE USING GTS (CAN BUS CHECK)

B

END

2.READ VALUE USING GTS (CAN BUS CHECK)
a.

Perform the CAN Bus Check using the GTS.

CAN Bus Check
50007
Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. B



b.

Turn the ignition switch off.



A

3.CHECK DTC OUTPUT (HEALTH CHECK)

B

3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Perform the Health Check using the GTS.


b.

Check for DTCs.

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



c.

Turn the ignition switch off.



A

4.READ VALUE USING GTS (EV MODE, EV MODE SWITCH)

B

GO TO DTC CHART

4.READ VALUE USING GTS (EV MODE, EV MODE SWITCH)
a.

Read the Data List using the GTS.

Powertrain > Hybrid Control > Data List
Tester Display
EV Mode
EV Mode Switch
50003 397 79,80
Result:
Result Proceed to
GTS display changes according to EV drive mode switch operation A
GTS display does not change according to EV drive mode switch operation B



b.

Turn the ignition switch off.



A

B

5.INSPECT EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)
5.INSPECT EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)

OK

6.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH - BODY GROUND)

NG

REPLACE EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH - BODY GROUND)
a.

Disconnect the P9 EV drive mode switch (pattern select switch assembly) connector.


b.
A443439C01
1.5,0.188 1.865,0.385 0.365,0.198 1.177,1.688 1.406,1.313 true 1.573,0.208 2.031,0.406 0.458,0.198 10 false P9 1.052,1.729 1.51,1.927 0.458,0.198 10 false E 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to EV Drive Mode Switch (Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P9-2 (E) - Body ground Always Below 1 Ω



c.

Reconnect the P9 EV drive mode switch (pattern select switch assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV DRIVE MODE SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV DRIVE MODE SWITCH)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.

Disconnect the P9 EV drive mode switch (pattern select switch assembly) connector.


c.
A443446C01
1.521,0.177 1.927,0.438 0.406,0.26 1.521,2.448 1.927,2.708 0.406,0.26 2.333,4.021 1.99,3.542 true 2.125,2.031 1.656,1.521 true 1.604,0.219 2.063,0.417 0.458,0.198 10 false H67 1.625,2.5 2.083,2.698 0.458,0.198 10 false P9 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 0.167,2.281 0.479,2.438 0.313,0.156 10 false *b 2.406,4.063 2.563,4.26 0.156,0.198 10 false S 2.063,2.073 2.573,2.354 0.51,0.281 10 false EVSW
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to EV Drive Mode Switch (Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-33 (EVSW) - P9-5 (S) Always Below 1 Ω
H67-33 (EVSW) or P9-5 (S) - Body ground Always 10 kΩ or higher



d.

Reconnect the P9 EV drive mode switch (pattern select switch assembly) connector.


e.

Reconnect the H67 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR