Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  P1AC000  Hybrid/EV Battery Cell Low Voltage  


DESCRIPTION

The hybrid vehicle control ECU controls the SOC (state of charge) of the HV battery at a constant level during driving. The HV battery is composed of 40 modules, and each module consists of six 1.2 V cells in series. The battery voltage sensor monitors battery block voltage at 12 locations.

A449772E01
0.094,0.854 1.833,1.625 1.74,0.771 10 false Hybrid Battery 0.104,1.031 2.25,1.229 2.146,0.198 10 false Block 11 Voltage 0.094,1.448 1.823,2.125 1.729,0.677 10 false Hybrid Battery 0.104,1.615 2.25,1.813 2.146,0.198 10 false Block 10 Voltage 0.094,2.146 1.823,2.823 1.729,0.677 10 false Hybrid Battery 0.094,2.333 2.24,2.531 2.146,0.198 10 false Block 9 Voltage 0.083,2.896 1.813,3.573 1.729,0.677 10 false Hybrid Battery 0.094,3.063 2.24,3.26 2.146,0.198 10 false Block 8 Voltage 0.083,3.583 1.813,4.26 1.729,0.677 10 false Hybrid Battery 0.083,3.76 2.333,4.24 2.25,0.479 10 false Block 7 Voltage 0.094,4.292 1.823,4.969 1.729,0.677 10 false Hybrid Battery 0.094,4.469 2.344,4.948 2.25,0.479 10 false Block 6 Voltage 0.083,5 1.813,5.677 1.729,0.677 10 false Hybrid Battery 0.083,5.177 2.333,5.656 2.25,0.479 10 false Block 5 Voltage 0.104,5.719 1.833,6.396 1.729,0.677 10 false Hybrid Battery 0.104,6.552 2.354,7.031 2.25,0.479 10 false Block 3 Voltage 0.115,6.385 1.844,7.063 1.729,0.677 10 false Hybrid Battery 0.104,5.885 2.354,6.365 2.25,0.479 10 false Block 4 Voltage 0.094,7 1.823,7.677 1.729,0.677 10 false Hybrid Battery 0.094,7.167 2.344,7.646 2.25,0.479 10 false Block 2 Voltage 0.104,7.573 1.833,8.25 1.729,0.677 10 false Hybrid Battery 0.104,7.75 2.354,8.229 2.25,0.479 10 false Block 1 Voltage 2.5,8.104 4.75,8.583 2.25,0.479 10 false Voltage Detection Relay Circuit 3.417,8.49 5.833,8.771 2.417,0.281 10 false Battery Voltage Sensor 2.063,0.802 3.802,1.573 1.74,0.771 10 false VB19 2.063,1.219 3.802,1.99 1.74,0.771 10 false VB18 2.063,1.927 3.802,2.698 1.74,0.771 10 false VB16 2.052,2.646 3.792,3.417 1.74,0.771 10 false VB14 2.052,3.375 3.792,4.146 1.74,0.771 10 false VB12 2.052,4.083 3.792,4.854 1.74,0.771 10 false VB10 2.052,4.802 3.792,5.573 1.74,0.771 10 false VB8 2.063,5.521 3.802,6.292 1.74,0.771 10 false VB6 2.063,6.229 3.802,7 1.74,0.771 10 false VB4 2.063,6.927 3.802,7.698 1.74,0.771 10 false VB2 2.073,7.323 3.813,8.094 1.74,0.771 10 false VB1 2.073,7.74 3.906,8.188 1.833,0.448 10 false GB0 2.688,0.604 4.427,1.375 1.74,0.771 10 false Connected to circuit A 2.688,1.573 4.427,2.344 1.74,0.771 10 false Connected to circuit C 2.677,7.552 4.49,7.948 1.813,0.396 10 false Connected to circuit A 2.677,7.135 4.49,7.531 1.813,0.396 10 false Connected to circuit B 2.677,6.583 4.49,6.979 1.813,0.396 10 false Connected to circuit C 2.688,5.875 4.5,6.271 1.813,0.396 10 false Connected to circuit C 2.688,5.167 4.5,5.563 1.813,0.396 10 false Connected to circuit C 2.677,4.448 4.49,4.844 1.813,0.396 10 false Connected to circuit C 2.688,3.729 4.5,4.125 1.813,0.396 10 false Connected to circuit C 2.688,2.281 4.5,2.677 1.813,0.396 10 false Connected to circuit C 2.688,1.01 4.427,1.781 1.74,0.771 10 false Connected to circuit B 4.208,3.469 6.021,3.865 1.813,0.396 10 false Circuit A 4.208,4.031 6.021,4.427 1.813,0.396 10 false Circuit B 4.208,4.875 6.021,5.271 1.813,0.396 10 false Circuit C 5.927,5.438 7.073,5.917 1.146,0.479 10 false Converter Circuit 5.938,5.271 7.083,5.75 1.146,0.479 10 false Analogue/Digital 2.688,3.01 4.5,3.406 1.813,0.396 10 false Connected to circuit C 0.104,0.271 1.844,1.042 1.74,0.771 10 false Hybrid Battery 0.104,0.448 2.25,0.646 2.146,0.198 10 false Block 12 Voltage 2.052,0.396 3.792,1.167 1.74,0.771 10 false VB20

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1AC000 Hybrid/EV Battery Cell Low Voltage Voltage difference between battery blocks is larger than the specified value due to an internal malfunction of the HV battery.
(2 trip detection logic)
·

Battery voltage sensor

·

HV battery

·

Hybrid battery terminal block


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P1AC000
·

Hybrid Battery Block 1 to 12 Voltage*1

·

Hybrid Battery SOC



HINT:
·

*1: Under normal conditions, the values of Hybrid Battery Block 1, 2, 11 and 12 Voltage will be approximately 16 V and Hybrid Battery Block 3, 4, 5, 6, 7, 8, 9 and 10 Voltage will be approximately 32 V.

·

If there is a short or open in a battery block voltage detection line, the value of Hybrid Battery Block Voltage for the corresponding battery block will be lower than 8 V.



The following items can be helpful when performing repairs:

Data List
·

Internal Resistance 1 to 12

·

Ready Signal

·

Vehicle Speed

·

Accelerator Position

·

Shift Position

·

Engine Speed

·

Hybrid Battery Voltage

·

Hybrid Battery Current

·

BATT Voltage

·

Hybrid Battery SOC of Immediately after IG ON

·

Hybrid Battery Maximum SOC

·

Hybrid Battery Minimum SOC

·

Total Distance Traveled

·

Distance from DTC Cleared

·

Engine Run Time


Vehicle Control History Data

Hybrid Battery Voltage Low


HINT:
·

This DTC can be stored after clearing DTCs and driving the vehicle for approximately 10 minutes. (As 2 trip detection logic is used, check for DTCs including pending DTCs.)

·

DTC P1AC000 is stored when a malfunction is detected in the HV battery or battery voltage sensor. If the HV battery is malfunctioning, the malfunction may not be reproduced when the condition of the HV battery changes due to a difference in driving load (amperage), SOC and battery temperature. Therefore, use the Freeze Frame Data when performing a repair.

(a)

When the HV battery is malfunctioning:

- Voltage of 1 or few battery blocks has dropped. The difference of voltage value between the hybrid battery block 1 and 2, 3 and 4, 4 and 5, 5 and 6, 6 and 7, 7 and 8, 8 and 9, 9 and 10 or 11 and 12 is 1.2 V or more.

- Voltage of all battery blocks is output randomly with no certain pattern.


(b)

When the battery voltage sensor is malfunctioning:

- Differences in battery block voltages have a certain pattern.



·

In order to ensure HV battery performance, appropriate cooling performance must be maintained. Perform the following items as necessary. If cooling performance has decreased and "Maintenance Required for Traction Battery Cooling Parts See Owner's Manual" is displayed on the multi-information display, make sure to perform the following items:

-

Make sure the air intake port is not blocked.

-

Make sure there are no gaps between the connecting parts of the ducts.

-

Clean the No. 2 HV battery intake filter (LH side and RH side).

Clear the DTCs to reset the learning values even if no DTCs are stored.





CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Drive the vehicle on urban roads for approximately 10 minutes.

HINT:

This DTC may not be stored if the vehicle is stopped or being driven at a constant speed.


7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00, P0AFC96, P308A12 or P0AFC62 is not output. A
P0AFC00, P0AFC96, P308A12 or P0AFC62 is also output. B


b.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Read output DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

b.

Using the GTS, make a note of the Freeze Frame Data item "Hybrid Battery Block 3 to 10 Voltage".


c.

Compare the Freeze Frame Data item "Hybrid Battery Block 3 to 10 Voltage" values with those shown in the following combination table.

Condition
"Hybrid Battery Block 3 Voltage" - "Hybrid Battery Block 4 Voltage" = 1.2 V or more
"Hybrid Battery Block 4 Voltage" - "Hybrid Battery Block 3 Voltage" = 1.2 V or more
"Hybrid Battery Block 4 Voltage" - "Hybrid Battery Block 5 Voltage" = 1.2 V or more
"Hybrid Battery Block 5 Voltage" - "Hybrid Battery Block 4 Voltage" = 1.2 V or more
"Hybrid Battery Block 5 Voltage" - "Hybrid Battery Block 6 Voltage" = 1.2 V or more
"Hybrid Battery Block 6 Voltage" - "Hybrid Battery Block 5 Voltage" = 1.2 V or more
"Hybrid Battery Block 6 Voltage" - "Hybrid Battery Block 7 Voltage" = 1.2 V or more
"Hybrid Battery Block 7 Voltage" - "Hybrid Battery Block 6 Voltage" = 1.2 V or more
"Hybrid Battery Block 7 Voltage" - "Hybrid Battery Block 8 Voltage" = 1.2 V or more
"Hybrid Battery Block 8 Voltage" - "Hybrid Battery Block 7 Voltage" = 1.2 V or more
"Hybrid Battery Block 8 Voltage" - "Hybrid Battery Block 9 Voltage" = 1.2 V or more
"Hybrid Battery Block 9 Voltage" - "Hybrid Battery Block 8 Voltage" = 1.2 V or more
"Hybrid Battery Block 9 Voltage" - "Hybrid Battery Block 10 Voltage" = 1.2 V or more
"Hybrid Battery Block 10 Voltage" - "Hybrid Battery Block 9 Voltage" = 1.2 V or more

A449773C01
5.406,1.854 5.906,1.854 false 1.031,3.344 1.49,3.688 0.458,0.344 10 false *a 1.333,3.354 1.76,3.656 0.427,0.302 10 false *b 1.781,3.354 2.229,3.656 0.448,0.302 10 false *c 2.25,3.333 2.656,3.646 0.406,0.313 10 false *d 2.698,3.354 3.104,3.646 0.406,0.292 10 false *e 3.167,3.354 3.563,3.625 0.396,0.271 10 false *f 3.625,3.344 4,3.688 0.375,0.344 10 false *g 4.073,3.365 4.625,3.719 0.552,0.354 10 false *h 4.573,3.354 5.052,3.698 0.479,0.344 10 false *i 5.042,3.333 5.438,3.646 0.396,0.313 10 false *j 5.542,3.354 5.938,3.615 0.396,0.26 10 false *k 1.073,3.531 1.479,3.792 0.406,0.26 10 false A 5.573,3.542 5.979,3.802 0.406,0.26 10 false B 5.875,3.542 6.281,3.802 0.406,0.26 10 false A 1.375,3.542 1.781,3.802 0.406,0.26 10 false B 2.26,3.542 2.667,3.802 0.406,0.26 10 false C 2.719,3.542 3.125,3.802 0.406,0.26 10 false C 3.188,3.542 3.594,3.802 0.406,0.26 10 false C 3.646,3.542 4.052,3.802 0.406,0.26 10 false C 4.104,3.542 4.51,3.802 0.406,0.26 10 false C 4.594,3.542 5,3.802 0.406,0.26 10 false C 0.125,0.094 2.719,0.542 2.594,0.448 10 false Check for HV Battery Malfunction 0.115,0.479 3.531,1.146 3.417,0.667 10 false (Example for when the difference of voltage value occurs between the hybrid battery block 9 and 10) 4.521,0.135 7.115,0.583 2.594,0.448 10 false A: Circuit A Hybrid Battery Block Voltage 4.521,0.458 7.115,0.906 2.594,0.448 10 false B: Circuit B Hybrid Battery Block Voltage 4.521,0.781 7.115,1.219 2.594,0.438 10 false C: Circuit C Hybrid Battery Block Voltage 5.958,1.771 6.948,2.083 0.99,0.313 10 false 1.2 V or more 5.865,3.354 6.26,3.615 0.396,0.26 10 false *l 1.813,3.542 2.219,3.802 0.406,0.26 10 false C 5.063,3.542 5.469,3.802 0.406,0.26 10 false C
*a Hybrid Battery Block 1 Voltage *b Hybrid Battery Block 2 Voltage
*c Hybrid Battery Block 3 Voltage *d Hybrid Battery Block 4 Voltage
*e Hybrid Battery Block 5 Voltage *f Hybrid Battery Block 6 Voltage
*g Hybrid Battery Block 7 Voltage *h Hybrid Battery Block 8 Voltage
*i Hybrid Battery Block 9 Voltage *j Hybrid Battery Block 10 Voltage
*k Hybrid Battery Block 11 Voltage *l Hybrid Battery Block 12 Voltage


Result:
Result Proceed to
On the HV battery blocks 3 to 10, one of the conditions in the table above is met. A
Other than above B



d.

Turn the ignition switch off.



A

3.CHECK TOTAL DISTANCE DRIVEN

B

5.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
3.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.

Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1
Other than above B


HINT:

*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.




A

B

4.REPLACE HV BATTERY
4.REPLACE HV BATTERY

NEXT

REPLACE HYBRID BATTERY TERMINAL BLOCK

5.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Read output DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

b.

Using the GTS, make a note of the Freeze Frame Data item "Hybrid Battery Block 1, 2, 11 and 12 Voltage".


c.

Compare the Freeze Frame Data item "Hybrid Battery Block 1, 2, 11 and 12 Voltage" values with those shown in the following combination tables.

Table 1
Circuit A Battery Block Circuit B Battery Block Condition
Hybrid Battery Block 1 Voltage Hybrid Battery Block 2 Voltage "Hybrid Battery Block 1 Voltage" - "Hybrid Battery Block 2 Voltage" = 1.2 V or more
Hybrid Battery Block 12 Voltage Hybrid Battery Block 11 Voltage "Hybrid Battery Block 12 Voltage" - "Hybrid Battery Block 11 Voltage" = 1.2 V or more

Table 2
Circuit A Battery Block Circuit B Battery Block Condition
Hybrid Battery Block 1 Voltage Hybrid Battery Block 2 Voltage "Hybrid Battery Block 2 Voltage" - "Hybrid Battery Block 1 Voltage" = 1.2 V or more
Hybrid Battery Block 12 Voltage Hybrid Battery Block 11 Voltage "Hybrid Battery Block 11 Voltage" - "Hybrid Battery Block 12 Voltage" = 1.2 V or more

A449774C01
1.417,1.75 1.552,1.156 1.552,1.156 1.292,1.156 false 5.177,1.76 5.094,1.188 5.094,1.188 5.438,1.188 false 0.656,4.458 0.458,3.698 0.458,3.698 0.74,3.698 false 6.083,4.458 6.427,3.75 6.427,3.75 6.167,3.75 false 0.771,2.677 1.146,2.99 0.375,0.313 10 false *a 1.063,2.677 1.469,2.99 0.406,0.313 10 false *b 1.677,2.677 2.167,3.24 0.49,0.563 10 false *c 2.115,5.344 2.479,5.646 0.365,0.302 10 false *d 2.573,2.677 2.979,3.031 0.406,0.354 10 false *e 3.021,2.677 3.49,2.938 0.469,0.26 10 false *f 3.479,2.667 3.854,3.042 0.375,0.375 10 false *g 3.927,2.667 4.333,3.083 0.406,0.417 10 false *h 4.396,2.677 4.833,3.073 0.438,0.396 10 false *i 4.833,2.667 5.302,3.135 0.469,0.469 10 false *j 5.354,2.667 5.771,3.021 0.417,0.354 10 false *k 0.781,5.333 1.156,5.646 0.375,0.313 10 false *a 1.042,5.344 1.448,5.656 0.406,0.313 10 false *b 1.667,5.344 2.083,5.646 0.417,0.302 10 false *c 2.125,2.677 2.573,3.104 0.448,0.427 10 false *d 2.573,5.344 2.979,5.698 0.406,0.354 10 false *e 3.021,5.344 3.49,5.604 0.469,0.26 10 false *f 3.479,5.333 3.854,5.708 0.375,0.375 10 false *g 3.927,5.344 4.344,5.594 0.417,0.25 10 false *h 4.385,5.344 4.823,5.74 0.438,0.396 10 false *i 4.833,5.344 5.302,5.698 0.469,0.354 10 false *j 5.354,5.333 5.771,5.688 0.417,0.354 10 false *k 0.802,2.885 1.156,3.25 0.354,0.365 10 false A 0.813,5.552 1.094,5.76 0.281,0.208 10 false A 5.396,5.552 5.792,5.823 0.396,0.271 10 false B 5.688,5.552 6.073,5.823 0.385,0.271 10 false A 1.083,2.885 1.458,3.198 0.375,0.313 10 false B 5.396,2.896 5.771,3.208 0.375,0.313 10 false B 1.083,5.552 1.49,5.802 0.406,0.25 10 false B 5.729,2.896 5.958,3.25 0.229,0.354 10 false A 1.698,2.885 2.094,3.156 0.396,0.271 10 false C 2.167,2.896 2.563,3.167 0.396,0.271 10 false C 2.615,2.885 3.01,3.156 0.396,0.271 10 false C 3.073,2.885 3.469,3.156 0.396,0.271 10 false C 3.979,2.885 4.375,3.156 0.396,0.271 10 false C 4.427,2.885 4.823,3.156 0.396,0.271 10 false C 1.708,5.552 2.104,5.823 0.396,0.271 10 false C 2.167,5.552 2.563,5.823 0.396,0.271 10 false C 3.083,5.552 3.479,5.823 0.396,0.271 10 false C 3.531,5.552 3.927,5.823 0.396,0.271 10 false C 3.979,5.552 4.375,5.823 0.396,0.271 10 false C 4.438,5.552 4.833,5.823 0.396,0.271 10 false C 0.135,0.083 3.823,0.594 3.688,0.51 10 false Check for Battery Voltage Sensor Malfunction 0.188,0.542 4.281,0.917 4.094,0.375 10 false All conditions in table 1 are met. 0.406,1.073 1.521,1.646 1.115,0.573 10 false 1.2 V or more 5.479,1.104 6.396,1.344 0.917,0.24 10 false 1.2 V or more 0.771,3.615 1.885,4.188 1.115,0.573 10 false 1.2 V or more 5.26,3.656 6.125,4.375 0.865,0.719 10 false 1.2 V or more 0.177,3.219 4.271,3.594 4.094,0.375 10 false All conditions in table 2 are met. 4.375,0.083 7.083,0.313 2.708,0.229 10 false A: Circuit A Hybrid Battery Block Voltage 4.375,0.396 7.135,0.719 2.76,0.323 10 false B: Circuit B Hybrid Battery Block Voltage 4.375,0.708 6.99,1.125 2.615,0.417 10 false C: Circuit C Hybrid Battery Block Voltage 5.688,2.667 6.104,3.021 0.417,0.354 10 false *l 3.531,2.896 3.927,3.167 0.396,0.271 10 false C 4.875,2.885 5.271,3.156 0.396,0.271 10 false C 5.656,5.344 6.073,5.698 0.417,0.354 10 false *l 4.875,5.552 5.271,5.823 0.396,0.271 10 false C 2.615,5.552 3.01,5.823 0.396,0.271 10 false C
*a Hybrid Battery Block 1 Voltage *b Hybrid Battery Block 2 Voltage
*c Hybrid Battery Block 3 Voltage *d Hybrid Battery Block 4 Voltage
*e Hybrid Battery Block 5 Voltage *f Hybrid Battery Block 6 Voltage
*g Hybrid Battery Block 7 Voltage *h Hybrid Battery Block 8 Voltage
*i Hybrid Battery Block 9 Voltage *j Hybrid Battery Block 10 Voltage
*k Hybrid Battery Block 11 Voltage *l Hybrid Battery Block 12 Voltage


HINT:

If an internal malfunction occurs in the battery voltage sensor, this symptom (difference in voltage of 1.2 V or more for certain pairs of blocks as shown in the illustration) will occur.


Result:
Result Proceed to
Either of the following conditions is met:
1. All conditions in table 1 are met.
2. All conditions in table 2 are met.
A
Other than above B



d.

Turn the ignition switch off.



A

B

6.CHECK TOTAL DISTANCE DRIVEN
6.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.

Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1
Other than above B


HINT:

*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.




A

B

7.REPLACE HV BATTERY
7.REPLACE HV BATTERY

NEXT

REPLACE HYBRID BATTERY TERMINAL BLOCK