Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  P30004B  Hybrid/EV Battery Control System Over Temperature  


DESCRIPTION

The hybrid vehicle control ECU monitors its internal operation and detects the following malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P30004B Hybrid/EV Battery Control System Over Temperature The HV battery temperature becomes too high due to a malfunction in the HV system.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid vehicle control ECU

·

HV battery


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P30004B
·

Hybrid Battery Temperature 1 to 6

·

Hybrid Battery Cooling Fan Intake Air Temperature 1

·

Ambient Temperature

·

Hybrid Battery Current

·

Hybrid Battery SOC

·

Hybrid Battery Cooling Fan 1 Drive Status

·

Hybrid/EV Battery Cooling Fan 2 Drive Status

·

Hybrid Battery Cooling Fan



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the Freeze Frame Data items "Vehicle Speed", "Hybrid Battery Temperature 1 to 6", "Hybrid Battery Cooling Fan Intake Air Temperature 1", "Ambient Temperature" and "Hybrid Battery Current".

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P30004B only is output. A
DTCs other than P30004B are also output. B



b.

Turn the ignition switch off.



A

2.CLEAN NO. 2 HV BATTERY INTAKE FILTER

B

2.CLEAN NO. 2 HV BATTERY INTAKE FILTER
a.
A449765C01
2.406,1.781 1.99,1.396 true 1.177,4.281 1.594,3.865 true 0.156,0.083 0.375,0.292 0.219,0.208 10 true *a 0.208,2.542 0.427,2.75 0.219,0.208 10 true *b 2.427,1.781 2.646,1.99 0.219,0.208 10 true *c 1.021,4.302 1.24,4.51 0.219,0.208 10 true *c
*a LH side
*b RH side
*c Intake Port


Check the HV battery cooling system intake port for blockage.

HINT:

If anything is blocking the HV battery cooling system intake port, remove it.



b.

Clean the No. 2 HV battery intake filter (LH side and RH side).

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY COOLING FILTER>INSPECTION


Result:
Proceed to
NEXT



NEXT

3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Read the Freeze Frame Data of DTC P30004B.

Powertrain > Hybrid Control > Trouble Codes
50001 397
NOTICE:
A408998C06
0.052,0.042 3.115,0.24 3.063,0.198 10 false Freeze Frame Data Recording Example 0.458,1.344 0.771,1.542 0.313,0.198 10 false *a 1.24,1.375 1.552,1.573 0.313,0.198 10 false *a 2.104,1.365 2.417,1.563 0.313,0.198 10 false *a 2.917,1.365 3.229,1.563 0.313,0.198 10 false *a 2.5,0.417 2.813,0.615 0.313,0.198 10 false *b 2.625,1.865 2.938,2.063 0.313,0.198 10 false *c 2.531,1.469 2.844,1.667 0.313,0.198 10 false *a
*a Freeze Frame Data Recorded
*b DTC Stored
*c Time


Although Freeze Frame Data is recorded before and after a DTC is stored, for this step it is only necessary to read the Freeze Frame Data recorded before "0s" (when the DTC was stored).


Result:
Result Proceed to
Other than below A
The difference between the value of "VL-Voltage before Boosting" and the total of "Hybrid Battery Block 1 to 12 Voltage" is 10 V or more. B



b.

Turn the ignition switch off.



A

4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

7.REPLACE BATTERY VOLTAGE SENSOR
4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Read the Freeze Frame Data of DTC P30004B.

NOTICE:

Although Freeze Frame Data is recorded before and after a DTC is stored, for this step it is only necessary to read the Freeze Frame Data recorded at "0s" (when the DTC was stored).


Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
Other than below A
The value of any of "Hybrid Battery Temperature 1 to 6" is 80°C (176°F) or more. B


b.

Turn the ignition switch off.



A

5.READ VALUE USING GTS (DATA LIST)

B

8.REPLACE HYBRID VEHICLE CONTROL ECU
5.READ VALUE USING GTS (DATA LIST)
a.

According to the display on the GTS, read the Data List and check that the value of each "Hybrid Battery Temperature 1 to 6" is 40°C (104°F) or less.

HINT:

If the value of any of "Hybrid Battery Temperature 1 to 6" is more than 40°C (104°F), turn the ignition switch off and wait until the values to decrease to 40°C (104°F) or less before continuing this procedure.


Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Temperature 1
Hybrid Battery Temperature 2
Hybrid Battery Temperature 3
Hybrid Battery Temperature 4
Hybrid Battery Temperature 5
Hybrid Battery Temperature 6
50003 397 198,199,200,201,202,203

b.

According to the display on the GTS, read the Data List and check the value of each "Hybrid Battery Block 1, 2, 11 and 12 Voltage" with the ignition switch ON.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 1 Voltage
Hybrid Battery Block 2 Voltage
Hybrid Battery Block 11 Voltage
Hybrid Battery Block 12 Voltage
50003 397 161,162,307,308
A449775C01
6.104,2.115 6.438,0.969 6.438,0.969 6.156,0.969 false 0.74,3.333 1.052,3.49 0.313,0.156 10 false *a 1.333,3.344 1.646,3.5 0.313,0.156 10 false *b 1.802,3.333 2.094,3.583 0.292,0.25 10 false *c 2.302,3.333 2.615,3.49 0.313,0.156 10 false *d 2.792,3.333 3.104,3.49 0.313,0.156 10 false *e 3.292,3.344 3.604,3.5 0.313,0.156 10 false *f 3.771,3.333 4.083,3.552 0.313,0.219 10 false *g 4.26,3.333 4.573,3.49 0.313,0.156 10 false *h 4.76,3.333 5.073,3.49 0.313,0.156 10 false *i 5.24,3.323 5.552,3.531 0.313,0.208 10 false *j 5.781,3.333 6.094,3.49 0.313,0.156 10 false *k 0.104,0.083 3.563,0.469 3.458,0.385 10 false Example for when a difference in the voltage value occurs between the hybrid battery block 2 and 11. 4.208,0.083 6.552,0.469 2.344,0.385 10 false A: Lowest hybrid battery block voltage 4.219,0.448 6.646,0.969 2.427,0.521 10 false B: Highest hybrid battery block voltage 1.365,3.542 1.521,3.74 0.156,0.198 10 false A 5.823,3.531 5.979,3.729 0.156,0.198 10 false B 5.292,0.854 6.208,1.198 0.917,0.344 10 false 0.3 V or more 6.396,3.333 6.708,3.49 0.313,0.156 10 false *l
*a Hybrid Battery Block 1 Voltage *b Hybrid Battery Block 2 Voltage
*c Hybrid Battery Block 3 Voltage *d Hybrid Battery Block 4 Voltage
*e Hybrid Battery Block 5 Voltage *f Hybrid Battery Block 6 Voltage
*g Hybrid Battery Block 7 Voltage *h Hybrid Battery Block 8 Voltage
*i Hybrid Battery Block 9 Voltage *j Hybrid Battery Block 10 Voltage
*k Hybrid Battery Block 11 Voltage *l Hybrid Battery Block 12 Voltage



Result:
Result Proceed to
Other than below A
The difference between the lowest and highest Hybrid Battery Block Voltage is 0.3 V or more. B


c.

Turn the ignition switch off.



A

6.READ VALUE USING GTS (DATA LIST)

B

8.REPLACE HYBRID VEHICLE CONTROL ECU
6.READ VALUE USING GTS (DATA LIST)
a.

According to the display on the GTS, read the Data List and check that the value of each "Hybrid Battery Temperature 1 to 6" is 40°C (104°F) or less.

HINT:

If the value of any of "Hybrid Battery Temperature 1 to 6" is more than 40°C (104°F), turn the ignition switch off and wait until the values to decrease to 40°C (104°F) or less before continuing this procedure.


Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Temperature 1
Hybrid Battery Temperature 2
Hybrid Battery Temperature 3
Hybrid Battery Temperature 4
Hybrid Battery Temperature 5
Hybrid Battery Temperature 6
50003 397 198,199,200,201,202,203

b.

According to the display on the GTS, read the Data List and check the value of each "Hybrid Battery Block 3 to 10 Voltage" with the ignition switch ON.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 3 Voltage
Hybrid Battery Block 4 Voltage
Hybrid Battery Block 5 Voltage
Hybrid Battery Block 6 Voltage
Hybrid Battery Block 7 Voltage
Hybrid Battery Block 8 Voltage
Hybrid Battery Block 9 Voltage
Hybrid Battery Block 10 Voltage
50003 397 163,164,165,166,167,168,169,170
A449776C01
4.115,1.594 4.375,1.073 4.375,1.073 4.635,1.073 false 0.656,3.344 0.969,3.5 0.313,0.156 10 false *a 1.104,3.344 1.417,3.5 0.313,0.156 10 false *b 1.656,3.333 1.969,3.49 0.313,0.156 10 false *c 2.198,3.344 2.51,3.5 0.313,0.156 10 false *d 2.74,3.333 3.052,3.49 0.313,0.156 10 false *e 3.281,3.344 3.594,3.5 0.313,0.156 10 false *f 3.813,3.333 4.125,3.656 0.313,0.323 10 false *g 4.417,3.344 4.729,3.5 0.313,0.156 10 false *h 4.958,3.344 5.271,3.5 0.313,0.156 10 false *i 5.5,3.333 5.813,3.49 0.313,0.156 10 false *j 6.031,3.344 6.344,3.5 0.313,0.156 10 false *k 0.094,0.083 3.563,0.458 3.469,0.375 10 false Example for when a difference in the voltage value occurs between the hybrid battery block 4 and 7. 4.542,0.104 6.948,0.51 2.406,0.406 10 false A: Lowest hybrid battery block voltage 4.552,0.521 7.01,0.969 2.458,0.448 10 false B: Highest hybrid battery block voltage 4.698,0.99 5.615,1.385 0.917,0.396 10 false 0.3 V or more 2.25,3.542 2.406,3.74 0.156,0.198 10 false A 3.865,3.552 4.021,3.75 0.156,0.198 10 false B 6.479,3.344 6.792,3.5 0.313,0.156 10 false *l
*a Hybrid Battery Block 1 Voltage *b Hybrid Battery Block 2 Voltage
*c Hybrid Battery Block 3 Voltage *d Hybrid Battery Block 4 Voltage
*e Hybrid Battery Block 5 Voltage *f Hybrid Battery Block 6 Voltage
*g Hybrid Battery Block 7 Voltage *h Hybrid Battery Block 8 Voltage
*i Hybrid Battery Block 9 Voltage *j Hybrid Battery Block 10 Voltage
*k Hybrid Battery Block 11 Voltage *l Hybrid Battery Block 12 Voltage



Result:
Result Proceed to
Other than below A
The difference between the lowest and highest Hybrid Battery Block Voltage is 0.3 V or more. B


c.

Turn the ignition switch off.



A

END

B

8.REPLACE HYBRID VEHICLE CONTROL ECU
7.REPLACE BATTERY VOLTAGE SENSOR

NEXT

8.REPLACE HYBRID VEHICLE CONTROL ECU

NEXT