Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  Shut Down Signal Circuit  


DESCRIPTION

The cause of the malfunction may be a shutdown signal.

Check whether there is a shutdown signal +B short circuit.

Related Parts Check
Area Inspection
HSDN terminal Check that the HSDN terminal voltage decreases to check for an open or short circuit while READY off (IG ON).
Hybrid vehicle control ECU, inverter, wire harness Check for open or short circuit in hybrid vehicle control ECU, inverter and wire harness.

SYSTEM DESCRIPTION

Power supply to the motor is cut off due to a shutdown signal sent from the hybrid vehicle control ECU to the motor generator control ECU (MG ECU).

WIRING DIAGRAM

A306450E66
2.417,0.344 2.729,0.542 0.313,0.198 10 false 36 2.417,0.698 2.729,0.896 0.313,0.198 10 false 35 2.417,1.073 2.729,1.271 0.313,0.198 10 false 6 2.417,1.396 2.729,1.594 0.313,0.198 10 false 9 2.417,1.75 2.729,1.948 0.313,0.198 10 false 8 4.552,1.021 4.865,1.219 0.313,0.198 10 false 6 4.563,1.51 4.875,1.708 0.313,0.198 10 false 3 3.333,0.49 4.813,0.771 1.479,0.281 10 false from PCU Fuse 4.469,1.208 4.781,1.406 0.313,0.198 10 false A31 4.792,1.073 5.323,1.323 0.531,0.25 10 false HSDN 4.813,1.688 5.344,1.938 0.531,0.25 10 false E1 4.74,2.271 6.917,2.688 2.177,0.417 10 false Hybrid Vehicle Control ECU 1.948,1.083 2.479,1.333 0.531,0.25 10 false HSDN 2.052,0.792 2.583,1.042 0.531,0.25 10 false +B2 2.125,0.458 2.656,0.708 0.531,0.25 10 false +B 1.927,1.51 2.458,1.76 0.531,0.25 10 false GND1 1.927,1.844 2.458,2.094 0.531,0.25 10 false GND2 0.469,2.219 0.99,2.448 0.521,0.229 10 false A55 0.469,2.365 2.646,2.594 2.177,0.229 10 false Inverter with Converter Assembly 4.479,1.698 4.76,1.896 0.281,0.198 10 false H67

Refer to the wiring diagram for the ECU Power Source Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>ECU Power Source Circuit

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK HYBRID VEHICLE CONTROL ECU
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

C407546C84
1.563,0.344 1.906,0.594 0.344,0.25 5.313,0.302 5.656,0.552 0.344,0.25 6.01,1.302 5.771,2.26 true 1.781,1.292 1.427,2.25 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.615,0.396 2.073,0.594 0.458,0.198 10 false A31 5.354,0.354 5.635,0.594 0.281,0.24 10 false H67 5.719,2.292 6.031,2.49 0.313,0.198 10 false E1 1.24,2.302 1.854,2.5 0.615,0.198 10 false HSDN
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A31-6 (HSDN) - H67-3 (E1) Ignition switch ON Below 4.5 V



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

SHUTDOWN SIGNAL CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.

Disconnect the A31 hybrid vehicle control ECU connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


f.
C412487C06
0.073,3.385 0.438,3.635 0.365,0.25 0.167,1.219 0.531,1.469 0.365,0.25 2.021,1.542 2.25,2.063 true 2.094,1.531 2.688,2.063 true 2.615,2.76 2.438,3.458 true 1.688,3.479 1.948,2.813 true 2.188,0.573 1.823,1.135 true 1.51,3.469 1.208,2.833 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.146,2.354 0.458,2.552 0.313,0.198 10 false *b 0.24,1.281 0.698,1.479 0.458,0.198 10 false A55 0.135,3.438 0.594,3.635 0.458,0.198 10 false A31 2.188,2.104 2.802,2.302 0.615,0.198 10 false +B2 2.208,0.385 2.823,0.583 0.615,0.198 10 false HSDN 1.906,2.625 2.521,2.823 0.615,0.198 10 false HSDN 0.865,2.656 1.479,2.854 0.615,0.198 10 false MREL 2.677,2.083 3.292,2.281 0.615,0.198 10 false +B 2.531,2.573 3.146,2.771 0.615,0.198 10 false +B1
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-6 (HSDN) or A31-6 (HSDN) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the hybrid vehicle control ECU and inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-6 (HSDN) - A55-36 (+B) Ignition switch off 10 kΩ or higher
A55-6 (HSDN) - A55-35 (+B2) Ignition switch off 10 kΩ or higher
A31-6 (HSDN) - A31-11 (+B1) Ignition switch off 10 kΩ or higher
A31-6 (HSDN) - A31-5 (MREL) Ignition switch off 10 kΩ or higher



j.

Reconnect the A31 hybrid vehicle control ECU connector.


k.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.
C410406C07
0.094,0.99 0.479,1.24 0.385,0.25 1.479,1.854 1.031,1.333 true 0.917,1.344 0.542,1.833 true 1.573,0.417 1.219,0.969 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.604,0.25 2.219,0.448 0.615,0.198 10 false HSDN 0.354,1.865 0.667,2.063 0.313,0.198 10 false +B 1.479,1.865 1.938,2.063 0.458,0.198 10 false +B2 0.156,1.021 0.615,1.219 0.458,0.198 10 false A55
*a Component without harness connected
(Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-6 (HSDN) - A55-36 (+B) Ignition switch off 10 kΩ or higher
A55-6 (HSDN) - A55-35 (+B2) Ignition switch off 10 kΩ or higher



d.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY