Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  P0A8196  Hybrid/EV Battery Cooling Fan 1 Component Internal Failure  P0A8198  Hybrid/EV Battery Cooling Fan 1 Component or System Over Temperature  P0A9696  Hybrid/EV Battery Cooling Fan 2 Component Internal Failure  P0A9698  Hybrid/EV Battery Cooling Fan 2 Component or System Over Temperature  


DESCRIPTION

Refer to the description for DTC P0A8111.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>P0A8111

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A8196 Hybrid/EV Battery Cooling Fan 1 Component Internal Failure The battery cooling blower assembly (No. 0) is malfunctioning and the actual speed is not within the specified range of the target speed calculated by the ECU.*
*: This DTC is not stored when "Hybrid Battery Cooling Fan 1 Frequency" is excessively low or high.
(2 trip detection logic)
·

Battery cooling blower assembly (No. 0)

·

Battery voltage sensor

·

No. 2 HV battery intake filter

·

No. 1 Hybrid battery intake duct

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0A8198 Hybrid/EV Battery Cooling Fan 1 Component or System Over Temperature The HV battery temperature is high and the battery cooling blower assembly (No. 0) is malfunctioning and the actual speed is not within the specified range of the target speed calculated by the ECU.*
*: This DTC is not stored when "Hybrid Battery Cooling Fan 1 Frequency" is excessively low or high.
(1 trip detection logic)
·

Battery cooling blower assembly (No. 0)

·

Battery voltage sensor

·

No. 2 HV battery intake filter

·

No. 1 Hybrid battery intake duct

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0A9696 Hybrid/EV Battery Cooling Fan 2 Component Internal Failure The battery cooling blower assembly (No. 1) is malfunctioning and the actual speed is not within the specified range of the target speed calculated by the ECU.*
*: This DTC is not stored when "Hybrid/EV Battery Cooling Fan 2 Frequency" is excessively low or high.
(2 trip detection logic)
·

Battery cooling blower assembly (No. 1)

·

Battery voltage sensor

·

No. 2 HV battery intake filter

·

No. 1 Hybrid battery intake duct

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0A9698 Hybrid/EV Battery Cooling Fan 2 Component or System Over Temperature The HV battery temperature is high and the battery cooling blower assembly (No. 1) is malfunctioning and the actual speed is not within the specified range of the target speed calculated by the ECU.*
*: This DTC is not stored when "Hybrid/EV Battery Cooling Fan 2 Frequency" is excessively low or high.
(1 trip detection logic)
·

Battery cooling blower assembly (No. 1)

·

Battery voltage sensor

·

No. 2 HV battery intake filter

·

No. 1 Hybrid battery intake duct

·

Wire harness or connector


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A8196
·

Hybrid Battery Cooling Fan 1 Drive Request

·

Hybrid Battery Cooling Fan 1 Drive Status

·

Hybrid Battery Cooling Fan 1 Frequency


P0A8198
P0A9696
·

Hybrid/EV Battery Cooling Fan 2 Drive Request

·

Hybrid/EV Battery Cooling Fan 2 Drive Status

·

Hybrid/EV Battery Cooling Fan 2 Frequency


P0A9698

The following items can be helpful when performing repairs:

Data List
·

Hybrid Battery Temperature 1 to 6

·

BATT Voltage


HINT:
·

"Hybrid Battery Cooling Fan 1 Frequency" is detected when the battery cooling blower assembly (No. 0) is operating and its value changes in proportion to the battery cooling blower assembly (No. 0) rotation speed.

·

"Hybrid/EV Battery Cooling Fan 2 Frequency" is detected when the battery cooling blower assembly (No. 1) is operating and its value changes in proportion to the battery cooling blower assembly (No. 1) rotation speed.



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON (READY) and turn the GTS on.

6.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

7.

Operate the battery cooling blower assembly in each fan mode, 1 through 6, for 60 seconds or more.

HINT:

Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.


8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00, P0AFC96 or P308A12 is not output. A
P0AFC00, P0AFC96 or P308A12 is output. B


b.

Turn the ignition switch off.



A

2.CHECK DTC

B

2.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
P0A8196 or P0A8198 is also output. A
P0A9696 or P0A9698 is also output. B



A

3.CHECK DUCT AND BLOWER

B

10.CHECK DUCT AND BLOWER
3.CHECK DUCT AND BLOWER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.

Check that the No. 2 HV battery intake filter, battery cooling blower assembly (No. 0) and No. 1 hybrid battery intake duct are not disconnected, damaged, or clogged with foreign matter.

A449754C01
2.292,1.125 2.833,1.396 true 5.656,0.375 5.052,0.74 true 6.073,1.563 5.427,1.198 true 2.865,1.333 3.073,1.51 0.208,0.177 10 true *1 5.698,0.229 5.885,0.417 0.188,0.188 10 true *2 6.115,1.51 6.302,1.698 0.188,0.188 10 true *3
*1 No. 2 HV Battery Intake Filter *2 Battery Cooling Blower Assembly (No. 0)
*3 No. 1 Hybrid Battery Intake Duct - -


OK:

The No. 2 HV battery intake filter, No. 1 hybrid battery intake duct and battery cooling blower assembly (No. 0) are not disconnected, damaged, or clogged with foreign matter.



d.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))

NG

CORRECT THE PROBLEM

4.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))

OK

5.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 0))

OK

6.CHECK BATTERY VOLTAGE SENSOR (GROUND SHORT CHECK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK BATTERY VOLTAGE SENSOR (GROUND SHORT CHECK)

b.
A449770C01
2.156,0.802 2.51,1.052 0.354,0.25 2.74,2.49 2.458,1.594 true 2.021,2.5 2.219,1.531 true 0.26,0.583 0.573,0.781 0.313,0.198 10 false *a 2.271,0.823 2.729,1.021 0.458,0.198 10 false y1 2.646,2.531 3.104,2.729 0.458,0.198 10 false GND 1.917,2.531 2.375,2.729 0.458,0.198 10 false SI0
*a Component without harness connected
(Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-5 (SI0) - y1-7 (GND) Ignition switch off 10 kΩ or higher



c.

Install the battery voltage sensor.


Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (HYBRID BATTERY COOLING FAN 1 FREQUENCY)

NG

7.READ VALUE USING GTS (HYBRID BATTERY COOLING FAN 1 FREQUENCY)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>P0A8111

Result:
Result Proceed to
Both of the values in the Data List (Hybrid Battery Cooling Fan 1 Frequency) and the actual measured value at the battery voltage sensor connector are 0 Hz. A
Other than above B



A

8.CHECK BATTERY VOLTAGE SENSOR

B

9.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
8.CHECK BATTERY VOLTAGE SENSOR

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 0)

NG

9.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 0)

NG

10.CHECK DUCT AND BLOWER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

c.

Check that the No. 2 HV battery intake filter, battery cooling blower assembly (No. 1) and No. 1 hybrid battery intake duct are not disconnected, damaged, or clogged with foreign matter.

A449755C01
1.125,1.427 1.531,1.146 true 4.885,0.458 5.396,0.802 true 4.781,1.521 5.354,1.219 true 0.875,1.354 1.083,1.531 0.208,0.177 10 true *1 4.677,0.323 4.865,0.51 0.188,0.188 10 true *2 4.573,1.469 4.76,1.656 0.188,0.188 10 true *3
*1 No. 2 HV Battery Intake Filter *2 Battery Cooling Blower Assembly (No. 1)
*3 No. 1 Hybrid Battery Intake Duct - -


OK:

The No. 2 HV battery intake filter, No. 1 hybrid battery intake duct and battery cooling blower assembly (No. 1) are not disconnected, damaged, or clogged with foreign matter.



d.

Install the rear floor silencer.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))

NG

CORRECT THE PROBLEM

11.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))

OK

12.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY (NO. 1))

OK

13.CHECK BATTERY VOLTAGE SENSOR (GROUND SHORT CHECK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK BATTERY VOLTAGE SENSOR (GROUND SHORT CHECK)

b.
A449770C04
2.156,0.802 2.51,1.052 0.354,0.25 2.74,2.49 2.458,1.594 true 1.927,2.479 2.156,1.51 true 0.26,0.583 0.573,0.781 0.313,0.198 10 false *a 2.26,0.844 2.719,1.042 0.458,0.198 10 false y1 2.646,2.531 3.104,2.729 0.458,0.198 10 false GND 1.813,2.531 2.271,2.729 0.458,0.198 10 false SI1
*a Component without harness connected
(Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
y1-6 (SI1) - y1-7 (GND) Ignition switch off 10 kΩ or higher



c.

Install the battery voltage sensor.


Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (HYBRID/EV BATTERY COOLING FAN 2 FREQUENCY)

NG

14.READ VALUE USING GTS (HYBRID/EV BATTERY COOLING FAN 2 FREQUENCY)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>P0A8111

Result:
Result Proceed to
Both of the values in the Data List (Hybrid/EV Battery Cooling Fan 2 Frequency) and the actual measured value at the battery voltage sensor connector are 0 Hz. A
Other than above B



A

15.CHECK BATTERY VOLTAGE SENSOR

B

16.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
15.CHECK BATTERY VOLTAGE SENSOR

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 1)

NG

16.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (NO. 1)

NG