Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  P0A9B1C  Hybrid/EV Battery Temperature Sensor "A" Voltage Out of Range  P0AC51C  Hybrid/EV Battery Temperature Sensor "B" Voltage Out of Range  P0ACA1C  Hybrid/EV Battery Temperature Sensor "C" Voltage Out of Range  P0AE81C  Hybrid/EV Battery Temperature Sensor "D" Voltage Out of Range  P0BC21C  Hybrid/EV Battery Temperature Sensor "E" Voltage Out of Range  P0C331C  Hybrid/EV Battery Temperature Sensor "F" Voltage Out of Range  


DESCRIPTION

These DTCs will be stored if the difference between the maximum and minimum output of each battery temperature sensor exceeds a certain amount and if the output of one battery temperature sensor deviates from that of the other sensors.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A9B1C Hybrid/EV Battery Temperature Sensor "A" Voltage Out of Range The performance of battery temperature sensor 0 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0AC51C Hybrid/EV Battery Temperature Sensor "B" Voltage Out of Range The performance of battery temperature sensor 1 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0ACA1C Hybrid/EV Battery Temperature Sensor "C" Voltage Out of Range The performance of battery temperature sensor 2 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0AE81C Hybrid/EV Battery Temperature Sensor "D" Voltage Out of Range The performance of battery temperature sensor 3 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0BC21C Hybrid/EV Battery Temperature Sensor "E" Voltage Out of Range The performance of battery temperature sensor 4 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0C331C Hybrid/EV Battery Temperature Sensor "F" Voltage Out of Range The performance of battery temperature sensor 5 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor (battery temperature sensor)

·

Wire harness or connector


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A9B1C Hybrid Battery Temperature 1 to 6
P0AC51C
P0ACA1C
P0AE81C
P0BC21C
P0C331C

HINT:

If the vehicle is left as is for 24 hours, the value of "Hybrid Battery Temperature" will be almost the same as the ambient temperature.


The following items can be helpful when performing repairs:

Data List
·

Vehicle Speed

·

Ambient Temperature


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With ignition switch ON and wait for 10 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00 or P0AFC96 is not output. A
P0AFC00 or P0AFC96 is also output. B


b.

Turn the ignition switch off.



A

2.CHECK INSTALLATION OF TEMPERATURE SENSOR (HYBRID BATTERY TEMPERATURE SENSOR)

B

2.CHECK INSTALLATION OF TEMPERATURE SENSOR (HYBRID BATTERY TEMPERATURE SENSOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>P0A9B2A

Result:
Result Proceed to
Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely. A
Claws are damaged. B
Any of battery temperature sensors are not installed correctly, but claws are not damaged. C



A

3.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

B

C

INSTALL PARTS CORRECTLY

3.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

OK

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
4.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)

OK

NG

REPAIR HARNESS OR CONNECTOR (BATTERY TEMPERATURE SENSOR)