The EV drive mode switch signal will be sent to the hybrid vehicle control ECU when the EV drive mode switch is operated. If the specified conditions are met, the system enters EV drive mode and the vehicle will be driven using EV drive mode. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter assembly to illuminate the EV drive mode indicator.
Depending on the condition of the hybrid control system and the driving conditions, the drive mode may not be able to be changed to EV drive mode and a warning message will be displayed on the multi-information display.
Under the following principal conditions, the drive mode will not be able to be changed to EV drive mode:
The hybrid control system is extremely hot.
The hybrid control system is extremely cold.
The engine is warming up.
The SOC (State of Charge) of the HV battery is low.
The vehicle is being driven at a speed higher than the specified value.
The accelerator pedal is being fully depressed or the vehicle is climbing a slope.
The defroster is on.
DTCs are stored.
Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV drive mode.
| Result | Proceed to |
|---|---|
| No buzzer sounded and no message was displayed on multi-information display | A |
| A buzzer sounded and a message was displayed on multi-information display | B |
If a buzzer sounds or a message is displayed on the multi-information display, one or more of the EV drive mode entry conditions have not been met.
A
B
Perform the CAN Bus Check using the GTS.
| Result | Proceed to |
|---|---|
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. | B |
Turn the ignition switch off.
A
B
Perform the Health Check using the GTS.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output | A |
| DTCs are output | B |
Turn the ignition switch off.
A
B
Read the Data List using the GTS.
| Tester Display |
|---|
| EV Mode |
| EV Mode Switch |
| Result | Proceed to |
|---|---|
| GTS display changes according to EV drive mode switch operation | A |
| GTS display does not change according to EV drive mode switch operation | B |
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>COMBINATION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the P9 EV drive mode switch (pattern select switch assembly) connector.
| *a | Front view of wire harness connector
(to EV Drive Mode Switch (Pattern Select Switch Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P9-2 (E) - Body ground | Always | Below 1 Ω |
Reconnect the P9 EV drive mode switch (pattern select switch assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H67 hybrid vehicle control ECU connector.
Disconnect the P9 EV drive mode switch (pattern select switch assembly) connector.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to EV Drive Mode Switch (Pattern Select Switch Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-33 (EVSW) - P9-5 (S) | Always | Below 1 Ω |
| H67-33 (EVSW) or P9-5 (S) - Body ground | Always | 10 kΩ or higher |
Reconnect the P9 EV drive mode switch (pattern select switch assembly) connector.
Reconnect the H67 hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG