Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420997 REAR MOTOR GENERATOR CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM  P0A799E  Drive Motor "B" Inverter Stuck On  P1C5E19  Drive Motor "B" Inverter Circuit Current Above Threshold  


DTC SUMMARY

MALFUNCTION DESCRIPTION


This DTC indicates that a large current flowed through the rear motor inverter. The cause of this malfunction may be one of the following:


Area Main Malfunction Description
Rear traction motor with transaxle assembly
·

Open or short circuit in the rear motor coils

·

Rear motor (MGR) internal malfunction (iron particles or damage from foreign objects)


Resolver Open or short circuit in the rear motor resolver
Rear motor inverter
·

Rear motor inverter internal circuit malfunction

·

Malfunction in ECU that controls the rear motor inverter

·

Rear motor inverter control sensor (current sensor, voltage sensors (VH, VL), etc.)


Inverter cooling system
·

Inverter water pump assembly malfunction

·

Coolant leak

·

Frozen

·

Blockage



DESCRIPTION

For a description of the inverter.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>P0D2D16

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A799E Drive Motor "B" Inverter Stuck On Rear motor inverter fail signal detected (circuit malfunction)
(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

Wire harness or connector

·

HV floor under wire (rear traction motor cable)

·

Motor cable

·

Hybrid vehicle transaxle assembly

·

Rear traction motor with transaxle assembly

·

PCU fuse

·

Inverter with converter assembly

·

Hybrid vehicle control ECU


Comes on Master Warning:
Comes on
P1C5E19 Drive Motor "B" Inverter Circuit Current Above Threshold Rear motor inverter fail signal detected:
A malfunction is detected in any of the rear motor components (rear motor inverter, rear motor, motor generator control ECU, etc.)
(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

Wire harness or connector

·

HV floor under wire (rear traction motor cable)

·

Motor cable

·

Hybrid vehicle transaxle assembly

·

Rear traction motor with transaxle assembly

·

PCU fuse

·

Inverter with converter assembly

·

Hybrid vehicle control ECU


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A799E
P1C5E19
Emergency Shutdown Signal

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With ignition switch ON and wait for 5 seconds or more.

7.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.

HINT:

Check that there are no abnormalities (abnormal sounds, coolant leaks, etc.).


8.

With the vehicle stopped, begin moving with the accelerator opening angle between 20% to 50% and a speed of approximately 10 km/h (6 mph), then stop the vehicle and repeat the same procedure several times.

HINT:

While doing this, check that the "Rear Motor Torque" value does not remain at 0 N*m continuously, but rather changes to indicate that the rear motor is operating.

(Unless rear motor torque is restricted due to DTC output, the rear motor torque will not remain at 0 N*m continuously.)


9.

Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the Generator Resolver Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Generator Resolver Circuit

Refer to the wiring diagram for the Motor Resolver Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Motor Resolver Circuit

Refer to the wiring diagram for the Rear Motor Resolver Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Rear Motor Resolver Circuit

Refer to the wiring diagram for the Generator High-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Generator High-voltage Circuit

Refer to the wiring diagram for the Motor High-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Motor High-voltage Circuit

Refer to the wiring diagram for the Rear Motor High-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Rear Motor High-voltage Circuit

Refer to the wiring diagram for the Inverter Low-voltage Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Inverter Low-voltage Circuit

Refer to the wiring diagram for the Cooling System.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Cooling System

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After troubleshooting and repairing all output DTCs, be sure to replace the inverter with converter assembly. (The inverter with converter assembly may have been broken or damaged due to overheating.)



PROCEDURE

1.GO TO MOTOR GENERATOR CONTROL SYSTEM
a.

Go to Motor Generator Control System.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>P0A799E

HINT:

For the P0A799E and P1C5E19 inspection procedures, refer to the Motor Generator Control System section.



Result:
Result
NEXT



NEXT

END