MALFUNCTION DESCRIPTION
This DTC indicates that the rear motor torque execution value does not correspond to the torque command value sent from the hybrid vehicle control ECU to the rear motor. The cause of this malfunction may be one of the following:
| Area | Main Malfunction Description |
|---|---|
| Inside of inverter | Inverter with converter assembly internal circuit malfunction |
| Rear traction motor with transaxle assembly | ·
Rear motor (MGR) internal malfunction (entry of foreign matter, etc.) ·
Open or short circuit in the rear motor coils |
| Inverter low-voltage circuit | The connectors are not connected properly |
| HV floor under wire (rear traction motor cable) | ·
Open circuit or poor insulation on HV floor under wire (rear traction motor cable) ·
Defective HV floor under wire (rear traction motor cable) connection |
| Hybrid vehicle control ECU | Hybrid vehicle control ECU internal circuit malfunction |
For a description of the inverter.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>P0D2D16
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0C1A00 | Drive Motor "B" Execution Torque Performance | Rear motor torque execution monitoring malfunction:
The difference between the rear motor torque requested by the motor generator control ECU and actual rear motor torque is large. (1 trip detection logic) |
·
Rear traction motor with transaxle assembly ·
Hybrid vehicle transaxle assembly ·
HV floor under wire (rear traction motor cable) ·
Motor cable ·
Inverter with converter assembly ·
Hybrid vehicle control ECU ·
Wire harness or connector |
Comes on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P0C1A00 | ·
Rear Motor Torque ·
Target Rear Motor Torque (Hybrid control system) ·
Vehicle Speed |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Turn the ignition switch to ON (READY) and wait for 5 seconds or more.
Move the shift lever to D, and then accelerate until the vehicle speed is 20 km/h (12.5 mph) and the accelerator position is approximately 25%.
Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Refer to the wiring diagram for the Generator High-voltage Circuit.
Refer to the wiring diagram for the Motor High-voltage Circuit.
Refer to the wiring diagram for the Rear Motor High-voltage Circuit.
Refer to the wiring diagram for the Shut Down Signal Circuit.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Go to Motor Generator Control System.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>P0C1A00
For the P0C1A00 inspection procedures, refer to the Motor Generator Control System section.
| Result |
|---|
| NEXT |
NEXT