Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C051D54  Multi-axis Acceleration Sensor Module "A" Missing Calibration  C121054  Yaw Rate Sensor Missing Calibration  


DESCRIPTION

The yaw rate sensor has a built-in acceleration sensor.

The No. 2 skid control ECU (brake actuator assembly) receives signals from the yaw rate sensor via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate sensor and the CAN communication system, DTC U012587 is output. When DTC U012587 is output together with C051D54 and/or C121054, inspect and repair the trouble areas indicated by U012587 first.


These DTCs are also output when the calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C051D54 Multi-axis Acceleration Sensor Module "A" Missing Calibration Zero point calibration of acceleration sensor undone.
·

Acceleration sensor zero point not calibrated

·

Acceleration sensor (yaw rate sensor) installation

·

Acceleration sensor (yaw rate sensor)

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
C121054 Yaw Rate Sensor Missing Calibration Zero point calibration of yaw rate sensor undone.
·

Yaw rate sensor zero point not calibrated

·

Yaw rate sensor installation

·

Yaw rate sensor

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

After replacing or reinstalling the yaw rate sensor, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs C051D54 and C121054 are not output. A
DTCs C051D54 and/or C121054 are output. B



A

END

B

4.CHECK YAW RATE SENSOR INSTALLATION
4.CHECK YAW RATE SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate sensor has been installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR>INSTALLATION

OK:

The yaw rate sensor is tightened to the specified torque.

The yaw rate sensor is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

NG

5.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Check the yaw rate and acceleration sensor output value displayed on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > Brake/EPB > Data List
Tester Display
Lateral G
Forward and Rearward G
Yaw Rate Sensor Value
50003 435 25,26,29
OK:

The yaw rate and acceleration sensor output value is normal.



Result:
Proceed to
OK
NG



OK

NG