The No. 2 skid control ECU (brake actuator assembly) controls the brake fluid pressure of each wheel cylinder based on the brake fluid pressure sensor.
DTCs may be stored if one of the following occurs:
Brake fluid leaks.
Wheel cylinder vibrates due to uneven wear of a brake disc.
Foreign matter enters a solenoid valve.
Line pressure drops during air bleeding.
Brake pads are replaced.
Rotors are replaced.
When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C13DB00 | Brake Pressure Too Low (Brake M/C1) | Fluid pressure control performance degraded (pressure excessively low) | ·
Brake fluid leaks ·
Uneven brake disc rotor wear ·
Wire harness and connector ·
Brake actuator assembly |
Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13DD00 | Brake Pressure Too Low (Brake M/C2) | Fluid pressure control performance degraded (pressure excessively low) | ·
Brake fluid leaks ·
Uneven brake disc rotor wear ·
Wire harness and connector ·
Brake actuator assembly |
Output ECU: No. 2 skid control ECU (brake actuator assembly) |
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
Interview the customer to check the vehicle conditions when the brake system warning light (yellow indicator) illuminated.
Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.
Freeze Frame Data is only stored once when a DTC is stored.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| Only DTCs C13DB00 and/or C13DD00 are output. | A |
| DTCs other than C13DB00 and/or C13DD00 are output. | B |
A
B
Based on the Freeze Frame Data or interview with the customer, inspect the following items for brake fluid leaks:
The brake lines from the brake booster with master cylinder assembly to each wheel cylinder.
The main body of the brake booster with master cylinder assembly and brake actuator assembly.
There are no fluid leaks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the A43 brake pedal stroke sensor assembly connector.
Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.
Brake pedal does not vibrate during braking.
An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.
The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.
If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.
Uneven disc wear can be checked by measuring the disc thickness variation.
for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION
for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Perform the air bleeding procedure in Bleed Brake System.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Measure the voltage and resistance on the wire harness side.
Voltage and resistance readings are all normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C13DB00 and C13DD00 are not output. | A |
| DTCs C13DB00 and/or C13DD00 are output. | B |
If the system returns to normal, it is suspected that a DTC was stored due to a poor connection of a terminal in a connector, air in the system, etc.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B