The No. 2 skid control ECU (brake actuator assembly) controls the brake fluid pressure of each wheel cylinder based on the brake fluid pressure sensor.
DTCs may be stored if one of the following occurs:
Brake fluid leaks.
Foreign matter enters a solenoid valve.
Line pressure drops during air bleeding.
Brake pads are replaced.
Rotors are replaced.
When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C13DC00 | Brake Pressure Too High (Brake M/C1) | Fluid pressure control performance degraded (pressure excessively high) | ·
Foreign matter in solenoid valve ·
Wire harness and connector ·
Brake actuator assembly |
Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13DE00 | Brake Pressure Too High (Brake M/C2) | Fluid pressure control performance degraded (pressure excessively high) | ·
Foreign matter in solenoid valve ·
Wire harness and connector ·
Brake actuator assembly |
Output ECU: No. 2 skid control ECU (brake actuator assembly) |
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
Interview the customer to check the vehicle conditions when the brake system warning light (yellow indicator) illuminated.
Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.
Freeze Frame Data is only stored once when a DTC is stored.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| Only DTCs C13DC00 and/or C13DE00 are output. | A |
| DTCs other than C13DC00 and/or C13DE00 are output. | B |
A
B
Clear the DTCs.
Perform the air bleeding procedure in Bleed Brake System.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Measure the voltage and resistance on the wire harness side.
Voltage and resistance readings are all normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C13DC00 and C13DE00 are not output. | A |
| DTCs C13DC00 and/or C13DE00 are output. | B |
If the system returns to normal, it is suspected that a DTC was stored due to a poor connection of a terminal in a connector or foreign matter in a solenoid valve, etc.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B