Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for Dynamic Torque Control AWD)
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0421146 REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL(for Dynamic Torque Control AWD) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL(for Dynamic Torque Control AWD)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear drive shaft oil seal replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: for RH Side

Rear wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Gas leaks from exhaust system*1 Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42340D 2.REMOVE REAR DRIVE SHAFT OIL SEAL

a.
C429346C01
0.74,0.688 0.979,0.323 0.979,0.323 1.25,0.323 true 1.917,2.677 2.188,2.885 2.188,2.885 2.406,2.885 true 2.427,2.813 2.74,3.01 0.313,0.198 10 true SST 1.292,0.25 1.51,0.438 0.219,0.188 10 false *1
*1 Rear Drive Shaft Oil Seal


Using SST, remove the rear drive shaft oil seal from the rear differential carrier assembly.

SST
09308-00010  

NOTICE:

Do not damage the rear differential carrier assembly.



Hide 42340D 3.INSTALL REAR DRIVE SHAFT OIL SEAL

a.
C429347C01
0.594,0.49 0.594,0.865 0.594,0.865 0.75,0.865 false 2.01,2.427 2.74,2.708 2.74,2.708 1.917,2.719 true 0.781,0.781 1.094,0.938 0.313,0.156 10 false *1 0.479,1.656 0.677,1.865 0.198,0.208 10 false A 2.771,2.635 3.135,2.844 0.365,0.208 10 true SST
*1 Rear Drive Shaft Oil Seal


Using SST and a hammer, install a new rear drive shaft oil seal to the rear differential carrier assembly.

SST
09223-46011  
09631-32020  

NOTICE:
·

Install the rear drive shaft oil seal uniformly.

·

Press fit the rear drive shaft oil seal straight.

·

Do not damage the rear drive shaft oil seal.

·

Do not damage the rear differential dust deflector.

·

Do not excessively press in the rear drive shaft oil seal.

·

Make sure to install the rear drive shaft oil seal as specified, otherwise a malfunction such as an oil leak may occur.



Standard Distance (A):

-0.4 to 0.4 mm (-0.00157 to 0.0157 in.)



b.

Apply a light coat of MP grease to the lip of the rear drive shaft oil seal.