Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY (for 2GR-FKS)
RM37A0E _52 Drivetrain _086862 DRIVE SHAFT / PROPELLER SHAFT _0421215 REAR DRIVE SHAFT ASSEMBLY(for 2GR-FKS) A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY(for 2GR-FKS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: for RH Side

Rear wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Gas leaks from exhaust system*1 Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 17430 1.REMOVE TAIL EXHAUST PIPE ASSEMBLY (for RH Side)

Hide 2.REMOVE REAR WHEEL

Hide 890C0A 4.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 5.REMOVE REAR SKID CONTROL SENSOR

Hide 48738 6.REMOVE REAR SUSPENSION ARM COVER

Hide 42312B 7.REMOVE REAR AXLE SHAFT NUT

Hide 8.SEPARATE REAR STABILIZER LINK ASSEMBLY

Hide 48231B 9.REMOVE REAR COIL SPRING

Hide 48258C 10.REMOVE REAR LOWER COIL SPRING INSULATOR

Hide 48740F 11.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY

Hide 48720A 12.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 48790 13.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY

Hide 14.DRAIN DIFFERENTIAL OIL

for Dynamic Torque Control AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT

for Dynamic Torque Vectoring AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT

Hide 42340B 15.REMOVE REAR DRIVE SHAFT ASSEMBLY

a.
C338275C02
2.781,0.958 2.01,1.729 2.01,1.729 2.948,1.292 true 1.854,1.656 2.167,1.813 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear drive shaft assembly and rear axle hub and bearing assembly.


b.
C338276

Using a plastic hammer, separate the rear drive shaft assembly from the rear axle hub and bearing assembly.

HINT:

If it is difficult to separate the rear drive shaft assembly from the rear axle hub and bearing assembly, tap the end of the rear drive shaft assembly using a brass bar and a hammer.



c.

Separate the rear drive shaft assembly from the rear axle carrier sub-assembly.

NOTICE:
·

Do not damage the rear disc brake dust cover sub-assembly.

·

Do not damage the rear drive shaft outboard joint boot.

·

Do not drop the rear drive shaft assembly.

·

Do not push the rear axle carrier sub-assembly towards the outside of the vehicle any further than necessary.




d.
C337311N02
1.458,1.333 1,2.365 1,2.365 1.667,1.375 true 0.854,2.417 1.313,2.615 0.458,0.198 10 false SST

Using SST, remove the rear drive shaft assembly.

SST
09520-01011  
09520-20010  (09521-02010, 09521-02040, 09521-02060)

NOTICE:
·

Do not damage the rear drive shaft oil seal or transmission coupling dust seal.

·

Do not damage the rear drive shaft inboard joint boot.

·

Do not drop the rear drive shaft assembly.

·

When removing the rear drive shaft assembly, keep it level.




Hide 42341C 16.REMOVE REAR DRIVE SHAFT SNAP RING

a.
C057543

Using a screwdriver, remove the rear drive shaft snap ring.