Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.11
RM37A0E _51 Engine / Hybrid System _094408 STOP AND START _0444545 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P253014  Ignition Switch Circuit Short to Ground or Open  


DESCRIPTION

If the engine stop and start ECU receives the off signal from the certification ECU (smart key ECU assembly) when communication with the ECM is normal, the engine stop and start ECU will store DTC P253014.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P253014 Ignition Switch Circuit Short to Ground or Open All of the following conditions are met for 10 seconds or more (1 trip detection logic):
·

Ignition switch off signal is input.

·

Communication with the ECM is normal.

·

Ignition switch (communication) to ON.


·

Wire harness or connector

·

Instrument panel junction block assembly

·

Certification ECU (Smart key ECU assembly)

·

Engine stop and start ECU


Does not come on DTC stored SAE Code: P2531

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

e.

Start the engine and warm it up.


f.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



g.

Depress the brake pedal and stop the vehicle.


h.

Keep the engine stopped by stop and start control for 10 second or more. (Keep the shift lever in D.)


i.

Release the brake pedal with the shift lever in D to start the engine.


j.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392


STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


WIRING DIAGRAM

A458137E02
0.615,6.938 1.688,7.135 1.073,0.198 10 false Battery 0.438,6.219 1.51,6.417 1.073,0.198 10 false FL MAIN 0.875,5.938 1.948,6.135 1.073,0.198 10 false J/B-B 0.74,3.458 1.813,3.656 1.073,0.198 10 false EFI-MAIN 2.604,3.99 3.677,4.188 1.073,0.198 10 false EFI-MAIN 2.042,7.031 4.719,7.344 2.677,0.313 10 false Instrument Panel Junction Block Assembly 2.594,2.51 3.667,2.708 1.073,0.198 10 false IG2 NO. 1 4.188,1.979 5.26,2.177 1.073,0.198 10 false ECU-IG2 NO. 1 4.333,3.458 5.406,3.656 1.073,0.198 10 false EFI NO. 6 3.417,5.927 4.49,6.125 1.073,0.198 10 false METER-IG2 0.698,1.99 1.771,2.188 1.073,0.198 10 false IG2-MAIN 2.76,6.531 3.833,6.729 1.073,0.198 10 false IG2-NO. 2 6.188,4.896 6.698,5.229 0.51,0.333 10 false +B 6.198,6.313 6.708,6.646 0.51,0.333 10 false IG2 5.708,6.698 7.083,7.188 1.375,0.49 10 false Engine Stop and Start ECU 6.198,3.75 6.708,4.083 0.51,0.333 10 false MREL 6.198,1.854 6.708,2.188 0.51,0.333 10 false IGSW 6,1.719 6.51,2.052 0.51,0.333 10 false 4 5.906,3.625 6.417,3.958 0.51,0.333 10 false 46 6.521,4.188 7.031,4.521 0.51,0.333 10 false ECM 6.146,4.188 6.656,4.521 0.51,0.333 10 false A28 2.469,1.729 2.979,2.063 0.51,0.333 10 false 3 3.25,3.208 3.76,3.542 0.51,0.333 10 false 5 3.24,1.729 3.75,2.063 0.51,0.333 10 false 5 3.24,2.156 3.75,2.49 0.51,0.333 10 false 2 2.469,2.135 2.979,2.469 0.51,0.333 10 false 1 2.479,3.625 2.99,3.958 0.51,0.333 10 false 1 3.24,3.625 3.75,3.958 0.51,0.333 10 false 2 2.479,3.219 2.99,3.552 0.51,0.333 10 false 3 2.01,1.115 4.948,1.365 2.938,0.25 10 false Certification ECU (Smart Key ECU Assembly) 3.083,0.708 3.594,1.042 0.51,0.333 10 false +B 2.531,0.708 3.042,1.042 0.51,0.333 10 false IG1D 2.281,0.583 2.792,0.917 0.51,0.333 10 false 17 3.354,0.583 3.865,0.917 0.51,0.333 10 false 4 2.146,5.792 3.219,5.99 1.073,0.198 10 false 4E 2.125,6.25 3.198,6.448 1.073,0.198 10 false 4A 4.313,6.25 5.385,6.448 1.073,0.198 10 false 4B 4.313,5.792 5.385,5.99 1.073,0.198 10 false 4B 4.313,5.573 5.385,5.771 1.073,0.198 10 false 32 4.375,6.042 5.448,6.24 1.073,0.198 10 false 3 2.156,5.583 3.229,5.781 1.073,0.198 10 false 1 2.125,6.042 3.198,6.24 1.073,0.198 10 false 17 5.76,4.906 6.271,5.24 0.51,0.333 10 false A34 5.708,6.302 6.219,6.635 0.51,0.333 10 false H66 5.781,6.083 6.292,6.417 0.51,0.333 10 false 18 5.833,4.677 6.344,5.01 0.51,0.333 10 false 1 2.021,0.958 2.531,1.292 0.51,0.333 10 false H48 2.646,5.167 3.719,5.365 1.073,0.198 10 false AM2 2.125,4.75 3.198,4.948 1.073,0.198 10 false 4A 2.135,4.542 3.208,4.74 1.073,0.198 10 false 44 2.125,6.708 3.198,6.906 1.073,0.198 10 false 4C 2.135,6.5 3.208,6.698 1.073,0.198 10 false 12

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the engine stop and start ECU or oil pump with solenoid assembly is replaced, check the oil pump with solenoid assembly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the Freeze Frame Data before troubleshooting. System condition information is recorded as Freeze Frame Data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (IG SWITCH)
a.

According to the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
IG Switch
50003 392 203
Result:
GTS Display Result Proceed to
IG Switch ON A
OFF B




A

B

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2-NO. 2 RELAY))
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2-NO. 2 RELAY))
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H66-18 (IG2) - 4B-32 Always Below 1 Ω
H66-18 (IG2) or 4B-32 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2-NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2-NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-1 - 4B-32 Battery positive (+) → 4A-17
Battery negative (-) → 4B-3
Below 1 Ω
4E-1 - 4B-32 Battery not connected to 4A-17 and 4B-3 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2-NO. 2 RELAY)

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-17 - 4C-12 Always Below 1 Ω
4A-17 or 4C-12 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2-NO. 2 RELAY) - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2-NO. 2 RELAY) - BODY GROUND)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2-NO. 2 RELAY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2-NO. 2 RELAY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-17 - H48-17 (IG1D) Always Below 1 Ω
4A-17 or H48-17 (IG1D) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the instrument panel junction block assembly 4B connector.

HINT:

Disconnect the IG1-NO. 1, IG1-NO. 2 and IG2-NO. 2 relays connected between the checked terminals as the coil inside the relay influences the measurement value.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (IG2 NO. 1 relay) - H48-17 (IG1D) Always Below 1 Ω
1 (IG2 NO. 1 relay) or H48-17 (IG1D) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the EFI-MAIN relay, FUEL PMP relay and A/F HTR relay from the No. 1 engine room relay block and No. 1 junction block assembly.

HINT:

Remove the FUEL PMP and A/F HTR relays connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-1 (+B) - 5 (EFI-MAIN relay) Always Below 1 Ω
A34-1 (+B) or 5 (EFI-MAIN relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK ECM (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK ECM (IGSW TERMINAL VOLTAGE)
a.
A457509C01
1.708,0.083 2.094,0.313 0.385,0.229 1.573,0.885 0.625,1.833 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.396,1.854 1.073,2.156 0.677,0.302 10 false IGSW 1.781,0.115 2.094,0.313 0.313,0.198 10 false A28
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-4 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.INSPECT EFI-MAIN RELAY

NG

10.INSPECT EFI-MAIN RELAY

OK

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPLACE EFI-MAIN RELAY

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
HINT:

If communication between the GTS and vehicle is possible and SFI system data can be read 30 seconds after turning the ignition switch off a malfunction in the EFI-MAIN relay circuit is suspected.


a.

Remove the EFI-MAIN relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN relay) - A28-46 (MREL) Always Below 1 Ω
2 (EFI-MAIN relay) or A28-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN RELAY)
A457147C01
0.063,0.063 0.375,0.26 0.313,0.198 10 false *1 0.344,1.604 0.656,1.802 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 EFI-MAIN Relay


a.

Remove the EFI-MAIN relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (EFI-MAIN RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN RELAY)

13.CHECK HARNESS AND CONNECTOR (EFI-MAIN RELAY - BODY GROUND)
a.

Remove the EFI-MAIN relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (IG1D TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (IG1D TERMINAL VOLTAGE)
B544504C04
4.563,0.469 4.958,0.698 0.396,0.229 4.01,2.188 4.25,1.323 true 4.635,0.5 4.948,0.698 0.313,0.198 10 false H48 3.854,2.229 4.281,2.458 0.427,0.229 10 false IG1D 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H48-17 (IG1D) - Body ground Ignition switch ACC Below 1 V
Ignition switch ON 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)