Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086893 PRE-COLLISION _0418188 PRE-COLLISION SYSTEM Y

PRE-COLLISION  PRE-COLLISION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the pre-collision system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.PRE-CHECK
2.PRE-CHECK
a.

for HV Model

i.

Measure the auxiliary battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



b.

for Gasoline Model

i.

Measure the auxiliary battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



c.

Check the fuses and relays.


d.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

3.INSPECT MULTI-INFORMATION DISPLAY
3.INSPECT MULTI-INFORMATION DISPLAY
a.

Check if a pre-collision system warning message is displayed on the multi-information display in the combination meter assembly.

HINT:

If more than one message is displayed, perform each inspection in the order listed in the table.



Result:
Result Proceed to
"VSC Turned OFF Pre-Collision Brake System Unavailable" is displayed A
"Pre-Collision System Malfunction Visit Your Dealer" is displayed B
"Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" is displayed C
Any of the following messages is displayed:
·

"Pre-Collision System Unavailable See Owner's Manual"

·

"Pre-Collision System Out of Temperature Range Unavailable See Owner's Manual"

·

"Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual"

·

"Front Camera Out of Temperature Range Unavailable Wait until Normal Temperature"

·

"Front Camera Low Visibility Unavailable See Owner's Manual"

·

"Front Camera Unavailable See Owner's Manual"


D
Warning message is not displayed E



A

B

4.CHECK CAN COMMUNICATION SYSTEM*

C

9.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY

D

6.CHECK VEHICLE CONTROL HISTORY*

E

13.PROBLEM SYMPTOMS TABLE
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check if the CAN communication system is functioning normally.

HINT:

Refer to CAN Bus Check in CAN Communication System.

for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM


OK:

CAN communication system is functioning normally.



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTCs*

NG

5.CHECK FOR DTCs*
a.

Using the GTS, check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

b.

Make a note of the output DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC C142571 is output B
DTCs other than C142571 are output C



A

6.CHECK VEHICLE CONTROL HISTORY*

B

C

8.RECONFIRM DTC OUTPUT*
6.CHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

b.

Record any output Vehicle Control History (RoB).


Result:
Result Proceed to
Vehicle Control History (RoB) codes are not output A
Vehicle Control History (RoB) code X2013, X2015, X2022, X2025, X2026 or X2028 is output B
Vehicle Control History (RoB) codes other than X2013, X2015, X2022, X2025, X2026 and X2028 are output C



A

B

GO TO VEHICLE CONTROL HISTORY (X2013, X2015, X2022, X2025, X2026 or X2028)

C

7.RECONFIRM VEHICLE CONTROL HISTORY*
7.RECONFIRM VEHICLE CONTROL HISTORY*
a.

Using the GTS, clear the Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

b.

Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

Result:
Result Proceed to
Vehicle Control History codes (RoB) are not output A
Vehicle Control History codes (RoB) are output B



A

B

8.RECONFIRM DTC OUTPUT*
a.

Using the GTS, clear the DTCs.

Body Electrical > Pre-Collision System > Clear DTCs
50002 432

b.

Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.

HINT:

Refer to each corresponding DTC for details on the detection conditions.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



c.

Using the GTS, check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

9.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check that there is no foreign matter such as dirt on or around the millimeter wave radar sensor assembly.

HINT:
·

A cover other than the dedicated radar sensor cover is not installed.

·

There is no dirt on the radar sensor cover or millimeter wave radar sensor assembly.

·

An accessory, such as bull bars, a grille guard, etc., which interferes with millimeter radio waves is not installed.

·

There is no sticker or coating applied to the dedicated radar sensor cover.

·

There is no foreign matter between the radar sensor cover and millimeter wave radar sensor assembly.




b.

If a problem is found, correct the problem as necessary.


Result:
Proceed to
NEXT



NEXT

10.INSPECT MULTI-INFORMATION DISPLAY
10.INSPECT MULTI-INFORMATION DISPLAY
NOTICE:

Before checking if the pre-collision system warning message is displayed on the multi-information, turn the ignition switch off then to ON.


a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Check if "Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" is displayed on the multi-information display.


Result:
Result Proceed to
Not displayed A
Displayed B



A

11.READ VALUE USING GTS

B

11.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Front Radar Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
On-Line Calibration Angle (Horizontal) Calibrated angle value (horizontal) Min.: -12.8 deg, Max.: 12.7 deg Learned value -
Body Electrical > Front Radar Sensor > Data List
Tester Display
On-Line Calibration Angle (Horizontal)
50003 429 40
OK:

The displayed value is between -0.5 and 0.5 degrees.



Result:
Proceed to
OK
NG



OK

12.EXPLAIN TO THE CUSTOMER

NG

12.EXPLAIN TO THE CUSTOMER
a.

Explain to the customer that "Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" was temporarily displayed on the multi-information display due to foreign matter such as dirt on or around the millimeter wave radar sensor assembly.


Result:
Proceed to
NEXT



NEXT

END

13.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table for the pre-collision system.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Problem symptoms are not listed in the Problem Symptoms Table. A
Problem symptoms are listed in the Problem Symptoms Table. B



A

14.INSPECT WARNING LIGHT

B

14.INSPECT WARNING LIGHT
a.

Check the condition of the warning lights.


Result:
Result Proceed to
The PCS warning light is not illuminated A
Only the PCS warning light is illuminated B



A

15.CHECK FOR DTCs* (Confirmed)

B

GO TO VEHICLE CONTROL HISTORY (X2015)

15.CHECK FOR DTCs* (Confirmed)
a.

Using the GTS, check for DTCs (Confirmed).

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

b.

Make a note of the output DTCs (Confirmed).


Result:
Result Proceed to
DTCs (Confirmed) are not output A
DTCs (Confirmed) are output B



A

16.CHECK VEHICLE CONTROL HISTORY*

B

19.GO TO DTC CHART
16.CHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, check for Vehicle Control History (RoB).

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

b.

Record any output Vehicle Control History (RoB).


Result:
Result Proceed to
Vehicle Control History codes (RoB) are not output A
Vehicle Control History codes (RoB) are output B



A

17.CHECK CONDITIONS WHEN PRE-COLLISION SYSTEM DID NOT OPERATE

B

GO TO VEHICLE CONTROL HISTORY

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY

HINT:

By using information obtained from the customer problem analysis and vehicle control history such as time of detection, trip number, etc., it may be possible to determine the cause of the malfunction.



17.CHECK CONDITIONS WHEN PRE-COLLISION SYSTEM DID NOT OPERATE
a.

Check if the exception conditions for the pre-collision system were met.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>PRECAUTION


Result:
Result Proceed to
The exception conditions were not met. A
The exception conditions were met. B



A

18.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*

B

END (The pre-collision system operated accordingly with the operation and prohibition conditions.)

18.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*
NOTICE:

Before checking for millimeter wave radar sensor beam axis misalignment, make sure that the radiator grille and front bumper are correctly installed and have not been damaged or modified.




c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Beam Axis Misalignment Reading.

Body Electrical > Front Radar Sensor > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 429 4405

g.

Check the amount of misalignment.

Standard:
Vertical Direction -5 to 5 deg.
Horizontal Direction -0.6 to 0.6 deg.


HINT:

The millimeter wave radar sensor assembly automatically calibrates the beam axis while the vehicle is being driven. The specified values apply to the automatic calibration only and do not apply during manual beam axis adjustment of the millimeter wave radar sensor assembly.



Result:
Result Proceed to
The beam axis values are within specification. A
The beam axis values are not within specification. B



A

B

19.GO TO DTC CHART
a.

Refer to each corresponding DTC (Confirmed) for details on the detection conditions.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
NEXT



NEXT

END