If the entry lock and wireless door lock operations cannot be performed, the door control receiver may be malfunctioning, or there may be wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR
After repair, confirm that no DTCs are output.
Inspect the fuses for circuits related to this system before performing the following procedure.
It is necessary to perform initialization after registration of the transmitter IDs into the electrical key and tire pressure warning ECU and receiver if the electrical key and tire pressure warning ECU and receiver has been replaced.*1
for initialization:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
for registration:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*2
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*1: for 12 Pin Type
*2: w/ Door Control Battery
Measure the auxiliary battery voltage.*1
Measure the auxiliary battery voltage with the ignition switch off.*2
*1: for Gasoline Model
*2: for HV Model
11 to 14 V
It may be possible to tell whether the auxiliary battery is discharged by operating the horn.
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
When the doors are locked by operating the entry lock function with all doors closed, check that the door ajar warning operates.
Be sure to check the following before performing the procedure.
Ignition switch is off.
All the doors is close.
The lock sensor is on or lock switch is pressed on the electrical key transmitter sub-assembly.
Electrical key transmitter sub-assembly is in the vehicle exterior detection area.
| Result | Proceed to |
|---|---|
| The wireless buzzer does not sound | A |
| The wireless buzzer sounds | B |
A
B
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Power door lock function operates normally | A |
| Power door lock function does not operate normally | B |
A
B
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the following antennas in key diagnostic mode.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (for driver door):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless buzzer sounds.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (for front passenger door):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless buzzer sounds.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (front floor):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| *a | Inspection Point |
Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (outside luggage compartment):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless buzzer sounds.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
Wireless buzzer sounds.
| Result | Proceed to |
|---|---|
| Key diagnostic mode inspections fail for both channels | A |
| Key diagnostic mode inspections succeed for both channels | B |
| Key diagnostic mode inspection succeeds for only one of the channels | C |
A
B
C
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.
*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| Wireless function does not operate normally | A |
| Wireless function operates normally | B |
A
B
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.
Even if the transmitter battery is depleted, it is still possible to start the engine*1 or hybrid control system*2 by holding the electrical key transmitter sub-assembly near the engine switch*1 or power switch*2, depressing the brake pedal and pressing the engine switch*1 or power switch*2.
*1: for Gasoline Model
*2: for HV Model
| Result | Proceed to |
|---|---|
| LED illuminates 3 times or more when switch is pressed and held | A |
| LED does not illuminate when switch is pressed and held | B |
| LED illuminates once or twice but not a third time | C |
A
B
C
Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.
| Result | Proceed to |
|---|---|
| Another registered electrical key transmitter sub-assembly is not available | A |
| Another registered electrical key transmitter sub-assembly is available | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using another registered electrical key transmitter sub-assembly, check that the function operates normally.
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
Disconnect the M5 certification ECU (smart key ECU assembly) connector.
Disconnect the M51*1 or M52*2 door control receiver connector.
*1: for 12 Pin Type
*2: for 5 Pin Type
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-18 (RCO) - M51-8 (+5) | Always | Below 1 Ω |
| M5-19 (RDAM) - M51-2 (DATA) | Always | Below 1 Ω |
| M5-20 (CSEL) - M51-6 (CSEL) | Always | Below 1 Ω |
| M51-12 (GND) - Body ground | Always | Below 1 Ω |
| M5-18 (RCO) or M51-8 (+5) - Other terminals and body ground | Always | 10 kΩ or higher |
| M5-19 (RDAM) or M51-2 (DATA) - Other terminals and body ground | Always | 10 kΩ or higher |
| M5-20 (CSEL) or M51-6 (CSEL) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-18 (RCO) - M52-4 (+5) | Always | Below 1 Ω |
| M5-19 (RDAM) - M52-5 (DATA) | Always | Below 1 Ω |
| M5-20 (CSEL) - M52-2 (CSEL) | Always | Below 1 Ω |
| M52-1 (GND) - Body ground | Always | Below 1 Ω |
| M5-18 (RCO) or M52-4 (+5) - Other terminals and body ground | Always | 10 kΩ or higher |
| M5-19 (RDAM) or M52-5 (DATA) - Other terminals and body ground | Always | 10 kΩ or higher |
| M5-20 (CSEL) or M52-2 (CSEL) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect all connectors and check that the function operates normally.
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
| *A | for 12 Pin Type |
| *B | for 5 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M51-12 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M52-1 (GND) - Body ground | Always | Below 1 Ω |
| *A | for 12 Pin Type |
| *B | for 5 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
| *b | Waveform 1 |
| *c | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *d | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M51-2 (DATA) - M51-12 (GND) | Procedure:
1.
Ignition switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms/DIV. | Below 1 V → Pulse generation
(See waveform 1) |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M52-5 (DATA) - M52-1 (GND) | Procedure:
1.
Ignition switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms/DIV. | Below 1 V → Pulse generation
(See waveform 1) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 12 Pin Type) | B |
| NG (for 5 Pin Type) | C |
A
B
C
| *A | for 12 Pin Type |
| *B | for 5 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M51-1 (IG) - M51-12 (GND) | Power switch on (IG) | 10 to 16 V |
| M51-6 (CSEL) - M51-12 (GND) | Procedure:
1.
Power switch off 2.
All doors closed |
Below 1 V → Pulse generation |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M52-2 (CSEL) - M52-1 (GND) | Procedure:
1.
Power switch off 2.
All doors closed |
Below 1 V → Pulse generation |
| *A | for 12 Pin Type |
| *B | for 5 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
| *b | Waveform 1 |
| *c | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *d | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M51-8 (+5) - M51-12 (GND) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M52-4 (+5) - M52-1 (GND) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) and perform registration again.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless function operates normally.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Wireless door lock function operates normally | A |
| Wireless door lock function does not operate normally | B |
A
B
OK
NG
Perform registration of the B code.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
After completing B code registration, check that the entry lock and unlock functions can be operated 2 times consecutively.
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| B Code | B code registration status | No Regd or Regd | No Regd: B code not registered correctly
Regd: B code registered correctly |
- |
| Tester Display |
|---|
| B Code |
| Result | Proceed to |
|---|---|
| "Regd" is displayed on the GTS | A |
| "No Regd" is displayed on the GTS | B |
A
B
Measure the voltage while checking the Data List on the GTS.
Read the Data List according to the display on the GTS.
| *A | for Gasoline Model | - | - |
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | All OFF, ACC ON, IG ON or ST ON | All OFF: Ignition switch off
ACC ON: Ignition switch ACC IG ON: Ignition switch ON ST ON: Sending engine*1 or hybrid control system*2 start request signal |
- |
| Tester Display |
|---|
| Power Supply Condition |
*1: for Gasoline Model
*2: for HV Model
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H48-17 (IG1D) - Body ground | Ignition switch off | Below 1 V |
| H48-16 (ACCD) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ACC SW | Ignition switch status | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ACC |
"ON" is also displayed when the ignition switch is ON. |
| IG SW | Ignition switch status | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ON |
"OFF" is also displayed when the ignition switch is ACC. |
| Tester Display |
|---|
| ACC SW |
| IG SW |
If the certification ECU (smart key ECU assembly) misjudges for any reason that the ignition switch is ON even though the ignition switch is off, the entry lock and unlock functions will be disabled.
| Result | Proceed to |
|---|---|
| The main body ECU (multiplex network body ECU) judges properly that the power source is off when the ignition switch is off | A |
| The main body ECU (multiplex network body ECU) does not judge properly that the power source is off when the ignition switch is off | B |
A
B
Disconnect and reconnect the certification ECU (smart key ECU assembly) connectors.
Check that the function operates normally.
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
Replace the certification ECU (smart key ECU assembly) and perform registration again.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the function operates normally.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Wireless door lock function operates normally | A |
| Wireless door lock function does not operate normally | B |
A
B
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.
*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| Wireless function does not operate normally | A |
| Wireless function operates normally 1 or more times. | B |
A
B
Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.
| Result | Proceed to |
|---|---|
| Another registered electrical key transmitter sub-assembly is not available | A |
| Another registered electrical key transmitter sub-assembly is available | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Enter key diagnostic mode and select the channel for which the wireless door lock buzzer did not sound and perform the inspection again using a different electrical key transmitter sub-assembly than was used in the initial inspection.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| Result | Proceed to |
|---|---|
| Wireless buzzer does not sound | A |
| Wireless buzzer sounds | B |
A
B
Disconnect the M51*1 or M52*2 door control receiver connector.
*1: for 12 Pin Type
*2: for 5 Pin Type
Disconnect the M5 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M51-6 (CSEL) - M5-20 (CSEL) | Always | Below 1 Ω |
| M51-6 (CSEL) or M5-20 (CSEL) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M52-2 (CSEL) - M5-20 (CSEL) | Always | Below 1 Ω |
| M52-2 (CSEL) or M5-20 (CSEL) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect all connectors and check that the function operates normally.
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
| *A | for 12 Pin Type |
| *B | for 5 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M51-6 (CSEL) - M51-12 (GND) | Procedure:
1.
Power switch off 2.
All doors closed |
Below 1 V → Pulse generation |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M52-2 (CSEL) - M52-1 (GND) | Procedure:
1.
Power switch off 2.
All doors closed |
Below 1 V → Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter key diagnostic mode and select the channel for which the wireless buzzer did not sound.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *A | for 12 Pin Type |
| *B | for 5 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
| *b | Waveform 1 |
| *c | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *d | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M51-2 (DATA) - M51-12 (GND) | Procedure:
1.
Ignition switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M52-5 (DATA) - M52-1 (GND) | Procedure:
1.
Ignition switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 12 Pin Type) | B |
| NG (for 5 Pin Type) | C |
A
B
C
Replace the certification ECU (smart key ECU assembly) and perform registration again.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the function operates normally.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Wireless door lock function operates normally | A |
| Wireless door lock function does not operate normally | B |
A
B