Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › from 2020.11
RM37A0E _53 Suspension _086865 FRONT SUSPENSION _0420325 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.

Install the 7 hole plugs to the front frame assembly.

HINT:

There are 2 different shapes of hole plug.


C424033N01
2.021,0.438 2.177,0.635 0.156,0.198 10 false A 2.156,0.719 2.313,0.917 0.156,0.198 10 false B 2.51,0.5 2.667,0.698 0.156,0.198 10 false A 1.917,0.594 2.073,0.792 0.156,0.198 10 false A 3.146,1.344 3.302,1.542 0.156,0.198 10 false A 3.719,1.333 3.875,1.531 0.156,0.198 10 false A 4.094,1.417 4.25,1.615 0.156,0.198 10 false A


Hide 32913 2.INSTALL OIL COOLER BRACKET

a.

Install the oil cooler bracket to the front frame assembly with the bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 17572B 3.INSTALL NO. 2 EXHAUST PIPE SUPPORT BRACKET (for A25A-FXS, A25B-FXS)

a.

Install the No. 2 exhaust pipe support bracket to the front frame assembly with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48069 4.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.


b.
C424031N01
0.635,0.531 0.74,0.677 0.104,0.146 10 false 1 1.229,0.292 1.323,0.427 0.094,0.135 10 true 2 2.823,0.625 2.958,0.875 0.135,0.25 10 false 3

Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt (1), (2) : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt (3) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48068 5.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 44250 6.INSTALL RACK AND PINION POWER STEERING GEAR ASSEMBLY

Hide 7.INSTALL FRONT STABILIZER BAR SUB-ASSEMBLY WITH LINK

Hide 8.INSTALL FRONT FRAME ASSEMBLY

a.

Install the rear engine mounting insulator to the front frame assembly with the 4 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


b.

Install the front engine mounting insulator to the front frame assembly with the 3 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 9.REMOVE ENGINE HANGERS (for 2GR-FKS)

Hide 45319 11.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)