Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › from 2020.11
RM37A0E _55 Steering _086876 STEERING GEAR / LINKAGE _0420315 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  INSTALLATION  


PROCEDURE

Hide 45319 1.INSTALL STEERING GEAR HEAT INSULATOR (for RHD)

a.
C447860N01
0.979,0.792 1.177,0.948 0.198,0.156 10 true 1 2.094,1.844 2.229,2.021 0.135,0.177 10 true 2 1.781,0.125 1.927,0.292 0.146,0.167 10 true 3

Install the steering gear heat insulator to the rack and pinion power steering gear assembly with the 3 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 45470 2.INSTALL TIE ROD ASSEMBLY LH

a.
C424048C01
1.438,0.552 1.875,0.552 1.875,0.552 1.875,1.25 true 1.667,1.26 1.667,0.563 true 1.24,0.469 1.542,0.625 0.302,0.156 10 false *a
*a Matchmark


Install the lock nut and tie rod assembly LH to the rack and pinion power steering gear assembly until the matchmarks are aligned.

HINT:

After adjusting the toe-in, tighten the lock nut.



Hide 45460 3.INSTALL TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 44250 4.INSTALL RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.

Install the rack and pinion power steering gear assembly to the front frame assembly with the 4 bolts and 4 new nuts.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 5.INSTALL FRONT STABILIZER BAR SUB-ASSEMBLY WITH LINK

a.

Install the front stabilizer bar sub-assembly with the 2 front stabilizer links to the front frame assembly with the 4 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

C427555N01
2.469,1.167 2.573,1.344 0.104,0.177 10 true A 2.448,2.271 2.563,2.438 0.115,0.167 10 true B 4.594,1.177 4.698,1.323 0.104,0.146 10 true C 4.615,2.271 4.719,2.417 0.104,0.146 10 true D

NOTICE:

Temporarily tighten the bolts in the order of (D), (C) and (B), and then fully tighten the 4 bolts in the order of (A), (B), (C), and (D).



Hide 6.INSTALL FRONT FRAME ASSEMBLY

Hide 7.REMOVE ENGINE HANGERS (for 2GR-FKS)

Hide 8.CONNECT WIRE HARNESS (for LHD)

a.

Install the wire harness to the rack and pinion power steering gear assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C424052


b.

Connect the wire harness connector to the rack and pinion power steering gear assembly.

HINT:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



Hide 9.CONNECT WIRE HARNESS (for RHD)

a.

Install the wire harness to the rack and pinion power steering gear assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C447862


b.

Connect the wire harness connector to the rack and pinion power steering gear assembly.

HINT:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



Hide 45319 10.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

a.
C424043N01
2.385,0.135 2.542,0.323 0.156,0.188 10 true 1 0.865,1.146 0.969,1.292 0.104,0.146 10 true 2

Install the steering gear heat insulator to the rack and pinion power steering gear assembly with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 45470 12.CONNECT TIE ROD ASSEMBLY LH

a.
C424040

Connect the tie rod assembly LH to the steering knuckle LH with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Do not damage the ball joint dust cover.

·

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.




b.

Install a new cotter pin.


Hide 45460 13.CONNECT TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45220 14.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C424039C01
1.104,2.865 1.677,2.865 true 1.292,2.875 1.292,2.948 1.292,2.948 1.646,2.948 true 0.917,2.771 1.083,2.938 0.167,0.167 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and rack and pinion power steering gear assembly.


b.

Connect the steering intermediate shaft assembly to the rack and pinion power steering gear assembly.


c.

Install a bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 15.INSTALL FRONT WHEELS

Hide 16.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 45470 17.FULLY TIGHTEN TIE ROD ASSEMBLY LH

a.
C424053C01
1.604,3.021 1.854,3.219 0.25,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using SST, tighten the tie rod assembly LH lock nuts.

SST
09612-24014  (09617-24011)

Torque:
Specified Tightening Torque : 88 N*m (897 kgf*cm, 65 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 52 mm (2.05 in.)) + torque wrench (fulcrum length of 255 mm (10.04 in.)): 73 N*m (744 kgf*cm, 54 ft.*lbf)




Hide 45460 18.FULLY TIGHTEN TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 19. TORQUE SENSOR ZERO POINT CALIBRATION