Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY › 2020.11–2021.10
RM37A0E _58 Vehicle Interior _086892 SUPPLEMENTAL RESTRAINT SYSTEMS _0421225 FRONT SEAT SIDE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Reclining motor (separate type front seatback spring assembly (driver seat))*

·

Slide motor (separate type front seat cushion spring assembly (driver seat))*


Initialize position control ECU Front Power Seat Control System (w/ Memory) (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Reclining motor (separate type front seatback spring assembly (driver seat))*

·

Slide motor (separate type front seat cushion spring assembly (driver seat))*


Initialize position control ECU Front Power Seat Control System (w/ Memory) (Click here)

CAUTION:
B394719

·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, separate type front seatback spring assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY

for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Hide 71074S 2.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Power Seat)

Hide 71868N 3.REMOVE FRONT SEAT FRONT CUSHION SHIELD (for Power Seat)

Hide 71812D 4.REMOVE FRONT SEAT CUSHION SHIELD (for Power Seat)

Hide 71862 5.REMOVE FRONT SEAT INNER CUSHION SHIELD (for Power Seat)

Hide 6.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Power Seat)

Hide 71930A 7.REMOVE FRONT SEAT HEADREST SUPPORT ASSEMBLY (for Power Seat)

Hide 8.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)

Hide 9.REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 71073S 10.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Manual Seat)

Hide 72494A 11.REMOVE FRONT SEAT VERTICAL ADJUSTER HANDLE (for Driver Side Manual Seat)

Hide 72551B 12.REMOVE RECLINING HINGE COVER (for Manual Seat)

Hide 72525A 13.REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

Hide 71848A 14.REMOVE SEAT ADJUSTER COVER CAP (for Driver Side Manual Seat)

Hide 71811D 15.REMOVE FRONT SEAT CUSHION SHIELD (for Manual Seat)

Hide 71861 16.REMOVE FRONT SEAT INNER CUSHION SHIELD (for Manual Seat)

Hide 17.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Manual Seat)

Hide 71930A 18.REMOVE FRONT SEAT HEADREST SUPPORT ASSEMBLY (for Manual Seat)

Hide 19.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)

Hide 73920A 20.REMOVE FRONT SEAT AIRBAG ASSEMBLY

CAUTION:
B417760C02
0.542,0.594 0.698,0.792 0.156,0.198 10 false .
V100155

Deployment Side


When storing the front seat airbag assembly, keep the airbag deployment side facing upward.


a.
B471942

Disengage the clamp.


b.

Remove the 2 nuts and front seat airbag assembly.

NOTICE:
·

Do not reuse the nuts.

·

Make sure that the separate type front seatback spring assembly is not deformed. If it is deformed, replace it with a new one.