1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT
Remove the front door scuff plate RH.
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Remove the cowl side trim sub-assembly RH.
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Remove the accelerator pedal pad.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>ACCELERATOR PEDAL SENSOR>REMOVAL
Remove the accelerator pedal.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>ACCELERATOR PEDAL SENSOR>REMOVAL
Check the brake pedal height.
Inspect and adjust the brake pedal height with the floor carpet and front floor mat folded back.
Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.
| *1 | Brake Pedal Pad | - | - |
| *a | Brake Pedal Height | *b | Measuring Plane of Floor Panel |
| *c | Ruler | *d | 36 mm (1.42 in.) |
158.6 to 174.6 mm (6.24 to 6.87 in.)
If the brake pedal height is not as specified, inspect and adjust the push rod length according to the procedure below.
Adjust the push rod length.
| *1 | Stop Light Switch Assembly |
| *2 | Lock Nut |
| *a | Measuring Plane of Floor Panel |
| *b | Brake Pedal Height |
Remove the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Loosen the lock nut.
Adjust the brake pedal height by turning the push rod.
158.6 to 174.6 mm (6.24 to 6.87 in.)
Tighten the lock nut.
Install the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
Install the accelerator pedal.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>ACCELERATOR PEDAL SENSOR>INSTALLATION
Install the accelerator pedal pad.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>ACCELERATOR PEDAL SENSOR>INSTALLATION
Install the cowl side trim sub-assembly RH.
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
Install the front door scuff plate RH.
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
89510D
2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY
Do not depress the brake pedal after turning the ignition switch to ON.
Inspect the brake pedal stroke sensor assembly.
Read the stroke sensor value without the brake pedal depressed.
| Tester Display |
|---|
| Stroke Sensor |
0.8 to 1.2 V
If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.
Adjust the brake pedal stroke sensor assembly.
Loosen the 2 nuts.
Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.
0.8 to 1.2 V
Fully tighten the 2 nuts.
Perform initialization and calibration.
3.INSPECT BRAKE PEDAL FREE PLAY
| *a | Brake Pedal Free Play |
Depress the brake pedal until a slight resistance is felt. Measure the distance as shown in the illustration.
1.0 to 6.0 mm (0.0394 to 0.236 in.)
If the brake pedal free play is not as specified, check the stop light switch clearance.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
If the brake pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.
4.INSPECT BRAKE PEDAL RESERVE DISTANCE
With the ignition switch ON (READY), depress the brake pedal and measure the brake pedal reserve distance.
| *1 | Brake Pedal Pad | - | - |
| *a | Brake Pedal Reserve Distance | *b | Measuring Plane of Floor Panel |
| *c | Hole of Floor Panel | *d | Ruler |
| *e | 36 mm (1.42 in.) | - | - |
110 mm (4.33 in.) or more