Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2020.11
RM37A0E _51 Engine / Hybrid System _086909 A25A-FXS, A25B-FXS INTAKE / EXHAUST _0416454 EXHAUST MANIFOLD A

A25A-FXS, A25B-FXS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

w/o Differential Pressure Sensor:

i.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold with the 6 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)



b.

w/ Differential Pressure Sensor:

i.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)



Hide 17141 2.INSTALL EXHAUST MANIFOLD

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold and No. 1 exhaust manifold heat insulator.

HINT:

At this time, do not install the parts with bolts or nuts.



c.
A479093C02
0.063,0.063 0.438,0.302 0.375,0.24 12 false *A 0.052,2.313 0.427,2.552 0.375,0.24 12 false *B 2.094,0.948 2.25,1.146 0.156,0.198 10 true 1 1.135,0.281 1.292,0.479 0.156,0.198 10 true 2 2.5,0.302 2.656,0.5 0.156,0.198 10 true 3 1.656,0.896 1.813,1.094 0.156,0.198 10 true 4 2.729,0.531 2.885,0.729 0.156,0.198 10 true 5 0.948,1.031 1.104,1.229 0.156,0.198 10 true 6 0.542,0.458 0.698,0.656 0.156,0.198 10 true 7 2.104,3.25 2.26,3.448 0.156,0.198 10 true 1 1.115,2.646 1.271,2.844 0.156,0.198 10 true 2 2.5,2.656 2.656,2.854 0.156,0.198 10 true 3 1.677,3.198 1.833,3.396 0.156,0.198 10 true 4 2.719,2.865 2.875,3.063 0.156,0.198 10 true 5 0.896,3.333 1.052,3.531 0.156,0.198 10 true 6 0.542,2.802 0.698,3 0.156,0.198 10 true 7
*A w/o Differential Pressure Sensor
*B w/ Differential Pressure Sensor


Temporarily install the exhaust manifold to the cylinder head sub-assembly with 7 new nuts.


d.

Tighten the 7 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

a.
A455278N01
3,1.323 3.156,1.521 0.156,0.198 10 true 1 0.385,1.198 0.542,1.396 0.156,0.198 10 true 2

Temporarily install the manifold stay to the exhaust manifold and cylinder block sub-assembly with the bolt and nut.


b.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

w/o Differential Pressure Sensor:

i.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

w/ Differential Pressure Sensor:

i.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 25706 5.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Differential Pressure Sensor)

a.
A479094C01
0.802,0.729 1.031,0.948 0.229,0.219 10 true *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install a new No. 1 vacuum transmitting pipe sub-assembly to the exhaust manifold.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf).




b.

Install the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 6.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17410 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install 2 new gaskets to the front exhaust pipe assembly.


b.

Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.


c.

Install the front exhaust pipe assembly to the exhaust manifold and tail exhaust pipe assembly with 2 new bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


d.
A454955C01
2.719,0.74 2.719,0.281 2.719,0.281 2.906,0.281 true 2.604,0.813 2.677,1.156 2.677,1.156 2.781,0.917 true 2.938,0.177 3.146,0.354 0.208,0.177 10 true *a 2.604,1.177 2.813,1.354 0.208,0.177 10 true *b
*a Tube
*b Wire Harness Clamp


Connect the air fuel ratio sensor (for sensor 2) connector.


e.

Engage the 2 wire harness clamps so that the tube is positioned as shown in the illustration.


Hide 55704B 9.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 10.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 11.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 12.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 13.INSTALL FRONT FENDER SPLASH SHEILD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 53808A 14.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 15.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 16.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 51420 18.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY