Home › Vehicle Exterior › WIPER / WASHER › WIPER ECU › from 2020.11
RM37A0E _59 Vehicle Exterior _086901 WIPER / WASHER _0417568 WIPER ECU A

WIPER / WASHER  WIPER ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during windshield wiper relay assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 73900 1.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

Hide 55308B 2.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD)

a.
E431218C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolts, nut and No. 3 instrument panel to cowl brace sub-assembly.


Hide 82878 3.REMOVE ECU INTEGRATION BOX LH (for LHD)

a.

Disconnect each connector.


b.
E431203C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Remove the nut, 2 bolts and ECU integration box LH.


Hide 85940 4.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (for LHD)

a.
E431204C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws to remove the windshield wiper relay assembly as shown in the illustration.

NOTICE:
·

If the ECU integration box LH is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.




Hide 67914 5.REMOVE FRONT DOOR SCUFF PLATE LH (for RHD)

Hide 62112A 6.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)

Hide 62312B 7.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)

Hide 55436A 8.REMOVE INSTRUMENT PANEL FINISH END PANEL LH (for RHD)

HINT:

Use the same procedure as for the LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55607 9.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for the LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55303B 10.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for the LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 85940 11.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (for RHD)

a.
B602598

Disconnect the 2 connectors.


b.
B602599

Remove the bolt.


c.

Disengage the guide to remove the windshield wiper relay assembly.