Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › from 2020.11
RM37A0E _58 Vehicle Interior _086898 INTERIOR PANELS / TRIM _0417352 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel safety pad sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 67914 2.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 3.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 62312B 4.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B564625

Disconnect the front door opening trim weatherstrip LH.


Hide 55436A 5.REMOVE INSTRUMENT PANEL FINISH END PANEL LH

a.

Using a moulding remover, disengage the 5 clips and 3 guides as shown in the illustration to remove the instrument panel finish end panel LH.

B564627C01
0,0 0,0 false
V113146

Insert Moulding Remover Here
V113147

Remove in this Direction



Hide 55650 6.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B564629C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 clips as shown in the illustration to remove the No. 1 instrument panel register assembly.


Hide 55044C 7.REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

a.
B570484C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 7 clips and 2 guides as shown in the illustration.


b.

Disconnect each connector to remove the instrument panel finish panel sub-assembly.


Hide 55410C 9.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B564633

Disengage the 2 claws and 4 clips to separate the instrument cluster finish panel assembly.


b.
B564634C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 9 clips and 2 guides as shown in the illustration to remove the instrument cluster finish panel assembly.


Hide 83100 10.REMOVE COMBINATION METER ASSEMBLY

Hide 45130 11.REMOVE HORN BUTTON ASSEMBLY

Hide 12.REMOVE STEERING WHEEL ASSEMBLY

Hide 45287 13.REMOVE LOWER STEERING COLUMN COVER

Hide 45286B 14.REMOVE UPPER STEERING COLUMN COVER

Hide 84329 15.REMOVE TURN SIGNAL SWITCH

Hide 84650 16.REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY

Hide 55606 17.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B564636

Remove the 3 screws <D>.


b.
B564637C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull the No. 1 instrument panel under cover sub-assembly in the direction indicated by the arrow (1) shown in the illustration to disengage the 2 claws.


c.

Pull the No. 1 instrument panel under cover sub-assembly in the direction indicated by the arrow (2) shown in the illustration to disengage the guide.


d.
B564639C01
2.167,1.833 1.75,1.365 true 2.125,1.854 2.438,2.01 0.313,0.156 10 false *a
*a DLC3


Disengage the 2 claws to disconnect the DLC3.


e.

Remove the No. 1 instrument panel under cover sub-assembly.


Hide 53601 18.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B564640

Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.


Hide 55045 19.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

a.
B564641C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 8 clips as shown in the illustration.


b.

Disconnect the connector to remove the lower instrument panel finish panel sub-assembly.


Hide 55446A 20.REMOVE NO. 1 SWITCH HOLE BASE

a.
B564643C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 6 clips as shown in the illustration.


b.
B564645C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the hook as shown in the illustration to remove the No. 1 switch hole base.


Hide 73900 21.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55405B 22.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B566128C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area shown in the illustration.


b.
B566129C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover, disengage the 5 clips and 4 guides as shown in the illustration to remove the center instrument cluster finish panel sub-assembly.


Hide 23.REMOVE RADIO AND DISPLAY ASSEMBLY WITH AIR CONDITIONING CONTROL (for 8 Inch Display)

Hide 24.REMOVE MULTI-DISPLAY WITH AIR CONDITIONING CONTROL (for 12.3 Inch Display)

Hide 55420A 25.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B564647

Remove the 2 screws <B>.


b.
B564649

Disconnect the connector.


c.
B564650C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 16 clips as shown in the illustration.


d.
B564648

Disengage the clamp to remove the center instrument cluster finish panel assembly.


e.

w/ Interior Illumination:

i.

Disconnect the 2 connectors.


ii.
B569936

Disengage the clamp.



Hide 26.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for 12.3 Inch Display)

Hide 67913 27.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62111A 28.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 29.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B564626

Disconnect the front door opening trim weatherstrip RH.


Hide 55435A 30.REMOVE INSTRUMENT PANEL FINISH END PANEL RH

a.

Using a moulding remover, disengage the 5 clips and 3 guides as shown in the illustration to remove the instrument panel finish end panel RH.

B568767C01
0,0 0,0 false
V113146

Insert Moulding Remover Here
V113147

Remove in this Direction



b.

w/ Airbag Cut Off Switch:

i.

Disconnect the connector.



Hide 55607 31.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B564653C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull the No. 2 instrument panel under cover sub-assembly in the direction indicated by the arrow (1) shown in the illustration to disengage the 4 claws.


b.

Pull the No. 2 instrument panel under cover sub-assembly in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 guides to remove it.


Hide 55303B 32.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

a.

Open the glove compartment door sub-assembly.


b.
B564655

Remove the 3 screws <D>.


c.

Close the glove compartment door sub-assembly.


d.
B564656

Remove the 2 bolts <A>.


e.
B564657C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 5 clips as shown in the illustration.


f.
B564659

Disconnect the connector.


g.

Disengage the clamp to remove the lower instrument panel sub-assembly.


Hide 62212B 33.REMOVE FRONT PILLAR GARNISH ASSEMBLY LH

Hide 55472C 34.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL

a.

Using a moulding remover, disengage the 2 clips and 2 guides as shown in the illustration to remove the No. 1 instrument panel speaker panel.

B564664C01
0,0 0,0 false
V113146

Insert Moulding Remover Here
V113147

Remove in this Direction



Hide 86160P 35.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

Hide 62211U 36.REMOVE FRONT PILLAR GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 55473B 37.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL

a.

Using a moulding remover, disengage the 2 clips and 2 guides as shown in the illustration to remove the No. 2 instrument panel speaker panel.

B564662C01
0,0 0,0 false
V113146

Insert Moulding Remover Here
V113147

Remove in this Direction



Hide 86160P 38.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 55981 39.REMOVE NO. 1 DEFROSTER NOZZLE GARNISH

a.
B566126C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 17 clips and 2 guides as shown in the illustration.


b.

Disconnect the connector to remove the No. 1 defroster nozzle garnish.


Hide 55434F 40.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

a.
B564660C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 4 clips as shown in the illustration.


b.

Disconnect each connector to remove the lower center instrument panel finish panel.


Hide 58817A 41.REMOVE FRONT NO. 2 CONSOLE BOX INSERT

a.
B566116

Remove the 2 screws <D>.


b.
B566117C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide as shown in the illustration.


c.
B566119C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 5 guides as shown in the illustration to remove the front No. 2 console box insert.


Hide 58816B 42.REMOVE FRONT CONSOLE BOX INSERT

a.
B566121

Remove the 2 screws <D>.


b.
B566122C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide as shown in the illustration.


c.
B566124C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 5 guides as shown in the illustration to remove the front console box insert.


Hide 55471A 43.REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT

a.
B564666C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 22 clips as shown in the illustration.


b.

Disconnect the connector to remove the instrument cluster finish panel ornament.


Hide 86740 44.REMOVE TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)

Hide 45.REMOVE TELEMATICS TRANSCEIVER WITH BRACKET (w/ Telematics Transceiver)

Hide 46.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

a.

for LHD:

i.

Disengage the 2 claws to disconnect the cooler (room temp. sensor) thermistor.

B595526C01
2.948,7.229 2.781,6.542 true 6.542,5.792 5.958,5.792 5.958,5.792 6.458,5.917 true 6.625,6.229 6.833,6.479 6.833,6.479 6.833,5.906 true 5.927,7.021 6.667,7.021 6.667,7.021 6.26,6.625 true 2.875,7.25 3.115,7.448 0.24,0.198 10 true *1 5.458,0.615 5.698,0.823 0.24,0.208 12 true *C 5.552,1.458 5.792,1.667 0.24,0.208 12 true *D 3.698,5.604 3.938,5.813 0.24,0.208 12 true *E 5.729,5.708 5.938,5.885 0.208,0.177 12 true *C 3.698,0.219 3.938,0.427 0.24,0.208 12 true *A 5.417,6.667 5.635,6.844 0.219,0.177 12 true *B 6.708,6.479 6.927,6.656 0.219,0.177 12 true *B 6.688,6.938 6.906,7.115 0.219,0.177 12 true *B
*A for 11 Speakers *B for 12.3 Inch Display
*C w/ Rear Seat Entertainment System *D w/ Telematics Transceiver
*E w/ Navigation System - -
*1 Cooler (Room Temp. Sensor) Thermistor - -



ii.

Remove the bolt <F>.


iii.

Disconnect each connector.


iv.

Disconnect the airbag connector.

HINT:

Refer to How to Connect or Disconnect Airbag Connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



v.

Disengage each clamp.



b.

for RHD:

i.

Disengage the 2 claws to disconnect the cooler (room temp. sensor) thermistor.

B595524C01
5.115,6.594 6.031,6.177 true 3.677,0.083 3.927,0.281 0.25,0.198 12 true *A 5.49,0.5 5.74,0.698 0.25,0.198 12 true *B 3.031,5.5 3.281,5.698 0.25,0.198 12 true *B 4.958,6.521 5.146,6.688 0.188,0.167 10 false *1 1,5.281 1.25,5.479 0.25,0.198 12 true *C
*A for 11 Speakers *B w/ Rear Seat Entertainment System
*C w/ Navigation System - -
*1 Cooler (Room Temp. Sensor) Thermistor - -



ii.

Remove the bolt <F>.


iii.

Disconnect each connector.


iv.

Disconnect the airbag connector.

HINT:

Refer to How to Connect or Disconnect Airbag Connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



v.

Disengage each clamp.



c.

Remove the 2 clips.

B566132C02
1.292,4.51 1.49,4.698 0.198,0.188 10 true *a 3.823,4.469 4.021,4.656 0.198,0.188 10 true *a 5.469,2.833 5.667,3.021 0.198,0.188 10 true *a 6.021,2.75 6.219,2.938 0.198,0.188 10 true *a 6.656,2.677 6.854,2.865 0.198,0.188 10 true *a 3.229,3.01 3.427,3.198 0.198,0.188 10 true *c 5.76,0.75 5.958,0.938 0.198,0.188 10 true *d 0.51,1.25 0.708,1.438 0.198,0.188 10 true *d 1.583,1.073 1.781,1.26 0.198,0.188 10 true *b 2.427,1.021 2.625,1.208 0.198,0.188 10 true *b
*a Bolt <A> *b Bolt <E>
*c Nut <C> *d Clip



d.

Remove the 5 bolts <A>, 2 bolts <E> and nut <C>.


e.

Disengage the 5 guides as shown in the illustration to remove the instrument panel safety pad sub-assembly.

B566133C01
0,0 0,0 false
V113147

Remove in this Direction - -


NOTICE:
·

Do not damage the instrument panel safety pad sub-assembly.

·

Do not allow the wire harnesses to interfere with the surrounding parts.